CALIBRATION
Troubleshooting · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008
| DESCRIPTION |
After replacing components relating to the VSC or performing "Front wheel alignment adjustment", clear and read the sensor calibration data.
Follow the chart to perform calibration.
Replacing Parts / Operation
Necessary Operation
Skid Control ECU
Yaw rate and deceleration sensor zero point calibration.
Yaw Rate Sensor
- Clearing zero point calibration data
- Yaw rate and deceleration sensor zero point calibration
Front Wheel Alignment Adjustment
- Clearing zero point calibration data
- Yaw rate and deceleration sensor zero point calibration
- Clearing zero point calibration data
| PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR FOR 2WD VEHICLES (When Using Intelligent Tester) |
- NOTICE:
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
- Perform this on a level surface (with an inclination of less than 1°).
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
Clear the zero point calibration data.
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG).
Operate the intelligent tester to erase the codes (select "Reset Memory").

- HINT:
- Refer to the intelligent tester operator's manual for further details.
Using the intelligent tester, perform the zero point calibration of the yaw rate and deceleration sensor.
- CAUTION:
- If the ignition switch is turned on (IG) for more than 15 seconds with the shift lever in the P position after zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under this condition, the skid control ECU will recognize that zero point calibration of the acceleration sensor is not completed and will indicate that there is a malfunction in the VSC system using the indicator lights and multi-information display.
Procedures for Test Mode.
A/T: Check that the shift lever is in the P position and apply the parking brake.
M/T: Check that the shift lever is in neutral and apply the parking brake.- NOTICE:
- DTCs C1210/36 and C1336/39 will be recorded if the shift lever is not in neutral (M/T) or the P position (A/T) (Click here).
Connect the intelligent tester to the DLC3.

Turn the ignition switch on (IG).
Set the intelligent tester to test mode (select "Test Mode").
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Obtain the zero point of the yaw rate and deceleration sensor.
Keep the vehicle stationary on a level surface for 2 seconds or more.
w/o Multi-information display:

Check that the VSC warning light blinks as shown in the illustration.- HINT:
- If the VSC warning light does not blink, perform the zero point calibration again.
- The zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared once.
- If zero point calibration is not completed normally during test mode, a DTC is stored.
- If the VSC warning light does not blink, perform the zero point calibration again.
w/ Multi-information display:
Check that the master caution indicator light blinks and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.- HINT:
- If the master caution indicator light does not blink and/or "VSC" is not displayed on the multi-information display, perform zero point calibration again.
- The zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared once.
If zero point calibration is not completed normally during test mode, a DTC is stored.
- If the master caution indicator light does not blink and/or "VSC" is not displayed on the multi-information display, perform zero point calibration again.
Turn the ignition switch off.
| PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR FOR 4WD VEHICLES AND 2WD VEHICLES (When not Using Intelligent Tester) |
- NOTICE:
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
- Perform this on a level surface (with an inclination of less than 1°).
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it stationary. (Do not start the engine.)
Clear the zero point calibration data.
Turn the ignition switch on (IG).
The warning light and indicator light come on for 3 seconds to indicate that the initial check is completed.
Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.

- SST
- 09843-18040
w/o Multi-information display:
Check that the VSC warning light comes on.
w/ Multi-information display:

Check that the master caution indicator light comes on and "CHECK VSC SYSTEM" is displayed on the multi-information display.Remove SST from the terminals of the DLC3.
Using a check wire, perform the zero point calibration of the yaw rate and deceleration sensor.
- CAUTION:
- w/o Multi-information display:
- If the ignition switch is turned on (IG) for more than 15 seconds with the shift lever in the P position after zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under this condition, the skid control ECU will recognize that zero point calibration of the acceleration sensor is not completed and will indicate that there is a malfunction in the VSC system using the indicator light.
- w/ Multi-information display:
- If the ignition switch is turned on (IG) for more than 15 seconds with the shift lever in the P position after zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under this condition, the skid control ECU will recognize that zero point calibration of the acceleration sensor is not completed and will indicate that there is a malfunction in the VSC system using the indicator lights and multi-information display.
Procedures for Test Mode.
Turn the ignition switch off.
Using SST, connect terminals 12 (TS) and (4) CG of the DLC3.

- SST
- 09843-18040
A/T:
Check that the shift lever is in the P position and apply the parking brake.M/T:
Check that the shift lever is in neutral and apply the parking brake.- NOTICE:
- DTCs C1210/36 and C1336/39 will be recorded if the parking brake switch is on (M/T) or shift lever is in the P position (A/T) (Click here).
Obtain the zero point of the yaw rate and deceleration sensor.
Turn the ignition switch on (IG).
Keep the vehicle stationary on a level surface for 2 seconds or more.
w/o Multi-information display:

Check that the VSC warning light blinks as shown in the illustration.- HINT:
- If the VSC warning light does not blink, perform the zero point calibration again.
- The zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared once.
- If the VSC warning light does not blink, perform the zero point calibration again.
w/ Multi-information display:
Check that the master caution indicator light blinks and "VSC" is displayed on the multi-information display (Test Mode) as shown in the illustration.- HINT:
- If the master caution indicator light does not blink and/or "VSC" is not displayed on the multi-information display, perform zero point calibration again.
- The zero point calibration is performed only once after the system enters test mode.
- Calibration cannot be performed again until the stored data is cleared once.
- If the master caution indicator light does not blink and/or "VSC" is not displayed on the multi-information display, perform zero point calibration again.
Turn the ignition switch off.