INSTALLATION
Removal / installation · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008
| 1.
INSTALL LOWER INSTRUMENT PANEL |
 |
Connect the connectors, attach the clamps and install the lower instrument panel.


w/ Illumination:
Connect the connectors.
for Automatic Air Conditioning System:
Install the cooler thermistor hose and connect the connector.
Attach the claws to install the DLC3.
Install the 4 bolts, 2 screws and 2 clips.
| 2.
INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
 |
- Attach the 3 claws to install the hood lock control lever.
| 3.
INSTALL POWER STEERING ECU ASSEMBLY |
 |
- Install the ECU with the 3 nuts.
Connect the connectors.
- NOTICE:
- Be sure to engage the lock of the connector as shown in the illustration.
| 4.
INSTALL INSTRUMENT PANEL BOX |
 |
- Attach the 6 clips to install the instrument panel box.
Install the screw.
| 5.
INSTALL NO. 1 SWITCH HOLE BASE |
 |
- Connect the connectors.
Attach the 4 clips to install the switch hole base.
| 6.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
 |
Attach the 3 claws to install the instrument panel under cover.
| 7.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL |
 |
Attach the 8 claws to install the lower instrument panel finish panel.
Install the 2 screws.
| 8.
INSTALL COWL SIDE TRIM BOARD RH
|
 |
- HINT:
- Use the same procedures described for the LH side.
| 9.
INSTALL COWL SIDE TRIM BOARD LH
|
 |
- HINT:
- Use the same procedures described for the LH side.
| 10.
INSTALL FRONT DOOR SCUFF PLATE RH
|
 |
- HINT:
- Use the same procedures described for the LH side.
| 11.
INSTALL FRONT DOOR SCUFF PLATE LH
|
 |
- Attach the 10 claws to install the scuff plate.
| 12.
INSTALL REAR CONSOLE BOX SUB-ASSEMBLY |
 |
Connect the connector.
- Install the rear console box with the 2 bolts and attach the wire harness clamp.
- Install the 2 screws.
| 13.
INSTALL CONSOLE BOX CARPET |
 |
- Install the console box carpet.
| 14.
INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH |
 |
- Attach the 2 claws to install the instrument panel bracket cover.
| 15.
INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH |
 |
- Attach the 2 claws to install the instrument panel bracket cover.
| 16.
INSTALL CONSOLE REAR END PANEL |
 |
- Attach the 6 claws to install the console rear end panel.
| 17.
INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY |
 |
- Connect the connector.
Attach the 4 clips to install the upper rear console panel.
| 18.
INSTALL CONSOLE CUP HOLDER BOX |
 |
- Attach the 2 clips to install the cup holder box.
Install the 2 screws.
| 19.
INSTALL SWITCH BASE |
 |
- Connect the connectors.
Attach the 2 clips and 2 claws to install the switch base.
| 20.
INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle) |
 |
- Connect the connector.
Attach the 2 clips and 4 claws to install the floor shift position indicator housing.
| 21.
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (for Manual Transaxle) |
 |
- Attach the 2 clips and 4 claws to install the upper console panel.
| 22.
INSTALL NO. 2 CONSOLE UPPER PANEL GARNISH |
 |
- Attach the 4 clips to install the upper panel garnish.
| 23.
INSTALL NO. 1 CONSOLE UPPER PANEL GARNISH |
 |
- Attach the 4 clips to install the upper panel garnish.
| 24.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY |
 |
- for Automatic Transaxle:
Twist the shift lever knob in the direction indicated by the arrow to install it.
- for Manual Transaxle:
Twist the shift lever knob in the direction indicated by the arrow to install it.
| 25.
INSTALL HEATER CONTROL SUB-ASSEMBLY (for Automatic Air Conditioning System)
|
 |
- Connect the connectors.
Attach the 3 clips to install the air conditioning control.
Install the 2 screws.
| 26.
INSTALL HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System)
|
 |
- Connect the connectors.
Attach the 3 clips to install the air conditioning control.
Install the 2 screws.
| 27.
INSTALL COMBINATION SWITCH ASSEMBLY
|
 |
Install the turn signal switch onto the steering column with the clamp.
| 28.
INSTALL SPIRAL CABLE SUB-ASSEMBLY
|
 |
Check that the front wheels are facing straight ahead.
Set the turn signal switch to the neutral position.
- NOTICE:
- Make sure that the turn signal switch is in the neutral position, as the pin of the turn signal switch may be snapped.
- Install the spiral cable.
- NOTICE:
- When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel.
Connect the connectors to the spiral cable.
- NOTICE:
- When handling the airbag connector, do not damage the airbag wire harness.
- Attach the 4 clips to the column cover (upper).
- Install the steering column cover (upper).
| 29.
INSTALL STEERING COLUMN COVER |
 |
for LHD:
Install the steering column cover (Click here).
for RHD:
Install the steering column cover (Click here).
| 30.
INSTALL INSTRUMENT PANEL SUB-ASSEMBLY |
 |
Install the instrument panel (Click here).
| 31.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 32.
CHECK SRS WARNING LIGHT |
 |
Check the SRS warning light (Click here).