2005-2008 RAV4 · Service Manual TRANSMISSION

REPLACEMENT

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. REPLACE TRANSAXLE HOUSING OIL SEAL LH
  1. Drain the automatic transaxle fluid.

    1. Remove the drain plug and gasket, and drain ATF.

    2. Install a new gasket and drain plug.

      Torque:
      47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. Remove the front drive shaft LH (Click here).

  1. D025835E01
    Remove the transaxle housing oil seal LH.

    1. Using SST, tap out the oil seal.

      SST
      09308-00010  

  1. D025836E01
    Install a new transaxle housing oil seal LH.

    1. Coat the lip of a new oil seal with MP grease.

    2. Using SST and a hammer, tap in the oil seal.

      SST
      09726-27012   (09726-02041)
      09950-70010   (09951-07200, 09951-07200)

      Standard depth:
      0 +-0.5 mm (0 +-0.020 in.)

  1. Install the front drive shaft LH (Click here).

  1. Add automatic transaxle fluid.

    Fluid type:
    Toyota Genuine ATF WS

  1. Inspect the transaxle fluid level (Click here).


2. REPLACE TRANSAXLE HOUSING OIL SEAL RH
  1. Remove the engine assembly with transaxle.

    1. for 1AZ-FE:
      Remove the engine with transaxle (Click here).

    2. for 2AZ-FE:
      Remove the engine with transaxle (Click here).

  1. Drain the automatic transaxle fluid.

    1. Remove the drain plug and gasket, and drain ATF.

    2. Install a new gasket and the drain plug.

      Torque:
      47 N*m{ 479 kgf*cm , 35 ft.*lbf }

  1. Remove the 3 bolts and drive shaft bearing bracket.

  1. Remove the 3 bolts and engine mount bracket RR.

  1. Remove the transfer assembly (Click here).

  1. D025618E01
    Remove the transaxle housing oil seal RH.

    1. Using a screwdriver with vinyl tape wound around its tip, remove the oil seal.

      NOTICE:
      Be careful not to damage the housing.

  1. D025837E01
    Install a new transaxle housing oil seal RH.

    1. Coat the lip of a new oil seal with MP grease.

    2. Using SST and a hammer, tap in the oil seal.

      SST
      09309-37010  

      Standard depth:
      6.0 +-0.5 mm (0.236 +-0.020 in.)

  1. Install the transfer assembly (Click here).

  1. Install the engine mount bracket RR with the 3 bolts.

    Torque:
    64 N*m{ 652 kgf*cm , 47 ft.*lbf }

  1. Install the drive shaft bearing bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. Install the engine assembly with transaxle.

    1. for 1AZ-FE:
      Install the engine with transaxle (Click here).

    2. for 2AZ-FE:
      Install the engine with transaxle (Click here).

  1. Add automatic transaxle fluid.

    Fluid type:
    Toyota Genuine ATF WS

  1. Inspect the fluid level (Click here).

← REPLACEMENT (Nov 2005 – Dec 2006)REPLACEMENT (from Aug 2007) →