Only Wireless Control Function is Inoperative
Circuit diagnosis · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 from Jan 2007
DESCRIPTION
The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all doors by sending lock / unlock signals to each door, and sends hazard flasher relay signals to the FLSH relay*1 (turn signal flasher relay *2).- HINT:
- *1: for LHD
- *2: for RHD
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS |
Check the wireless door lock control functions (Click here).
- OK:
- Each function of wireless door lock control system operates normally using transmitter switch.
|
|
||||
| NG | |
| 2. CHECK TRANSMITTER LED ILLUMINATION |
Check that the transmitter's LED illuminates 3 times when the switch is pressed 3 times.
- OK:
- Transmitter's LED illuminates 3 times when switch is pressed 3 times.
|
|
||||
| OK | |
| 3. CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS (STANDARD OPERATION FUNCTION) |
- HINT:
- Use the following standard test procedure to check the transmitter again.
Hold the transmitter approximately 1 m (3.28 ft.) from the driver side door outside handle. The transmitter must be held parallel to the ground and perpendicular to the side of the vehicle.
Press and hold either the LOCK or UNLOCK transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.
- OK:
- Doors can be locked and unlocked with transmitter switches.
|
|
||||
| OK | |
| 4. REPLACE TRANSMITTER BATTERY |
Temporarily replace the transmitter battery with a new or normally functioning one (Click here).
Check that the doors can be locked and unlocked using the transmitter switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
| 5. CHECK ROOM LIGHT |
Check that the room light illumination operates normally.
- OK:
- Room light illumination operates normally.
|
|
||||
| OK | |
| 6. SWITCH TO SELF-DIAGNOSTIC MODE |
![]() ![]() |
Switch to self-diagnostic mode by operating the ignition key cylinder.
Make sure the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds of removing the key, insert the key into the ignition key cylinder (ignition switch OFF). Then turn the ignition switch ON and OFF.
Within 30 seconds of turning the ignition switch OFF, perform the following operation 9 times: turn the ignition switch ON and OFF.
- NOTICE:
- If the system cannot enter self-diagnostic mode, the system returns to normal mode.
- HINT:
- Turning the ignition switch ON after the above operations have been completed ends self-diagnostic mode.
- Do not lock or unlock doors during self-diagnostic mode.
- Turning the ignition switch ON after the above operations have been completed ends self-diagnostic mode.
Check that the system has switched to self-diagnostic mode by checking the room light flash pattern.
- OK:
- Flash pattern is same as illustration.
|
|
||||
| OK | |
| 7. CHECK BY SELF-DIAGNOSTIC MODE |


Inspect the diagnosis outputs when the door control transmitter switch is held down. The diagnosis outputs can be checked by the flash patterns of the room light.
Result: Result
Proceed to
Unmatching recognition code is output
A
Normal waves (light flash pattern) is output
B
No diagnosis outputs
C
|
|
||||
|
|
||||
| A | |
| 8. REGISTER RECOGNITION CODE |
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).
- OK:
- Recognition code can be registered.
|
|
||||
| OK | ||
| ||
| 9. CHECK DOOR CONTROL TRANSMITTER (RESPONSE) |
Temporarily replace the door control receiver with a new or normally functioning one.
Held down the door control transmitter's switch.
Check that an unmatching recognition code is output.
- OK:
- Unmatching recognition code is output.
|
|
||||
| NG | |
| 10. CHECK DOOR CONTROL RECEIVER (OPERATION) |
Temporarily replace the door control receiver (Click here, Click here) with a new or normally functioning one.
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||
| 11. CONFIRM PROCEDURES TO ENTER SELF-DIAGNOSTIC MODE |
| Result |
Proceed to |
| Self-diagnostic mode entry successful |
A |
| Self-diagnostic mode entry unsuccessful |
B |
|
|
||||
| A | |
| 12. INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
![]() ![]() |
Remove the switch.
Measure the resistance of the switch.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Not pushed
10 kΩ or higher
Pushed
Below 1 Ω
|
|
||||
| OK | |
| 13. CHECK WIRE HARNESS (UNLOCK WARNING SWITCH - MAIN BODY ECU AND BODY GROUND) |
![]() ![]() |
Disconnect the L9 switch connector.
Disconnect the E20 junction block connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
L9-1 - IE-26 (KSW)
Below 1 Ω
L9-2 - Body ground
L9-1 or IE-26 (KSW) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 14. CHECK DOOR CONTROL RECEIVER (OUTPUT) |
![]() ![]() |
Reconnect the L10 receiver connector.
Measure the voltage of the connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
L10-2 (RDA) - Body ground
Ignition switch off, all doors closed and transmitter switch not pressed
11 to 14 V
Ignition switch off, all doors closed and transmitter switch pressed
Pulse generation
|
|
||||
| NG | |
| 15. CHECK DOOR CONTROL TRANSMITTER MODULE (OPERATION) |
Temporarily replace the door control transmitter module with a new or normally functioning one (Click here).
Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.
- OK:
- Doors can be locked and unlocked with transmitter.
|
|
||||
| OK | ||
| ||




