2005-2008 RAV4 · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. INSTALL MANUAL TRANSAXLE CASE PROTECTOR

D030076E02
  1. Install the case protector with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


2. INSTALL MANUAL TRANSAXLE ASSEMBLY

D025747E02
  1. Align the input shaft with the clutch disc and install the transaxle to the engine.

  1. Install the 10 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for bolt A
    46 N*m{ 469 kgf*cm , 34 ft.*lbf } for bolt B
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for bolt C


3. INSTALL STIFFENER PLATE RH

C127241
  1. Install the stiffener plate with the 4 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }


4. INSTALL STIFFENER PLATE LH

C127240
  1. Install the stiffener plate with the 4 bolts.

    Torque:
    46 N*m{ 469 kgf*cm , 34 ft.*lbf }


5. INSTALL OIL PAN INSULATOR

C127239
  1. Install the insulator with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


6. INSTALL REAR ENGINE MOUNTING BRACKET

C132028
  1. Install the bracket with the 3 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }


7. INSTALL ENGINE MOUNTING BRACKET LH

C129226
  1. Install the bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


8. INSTALL FRONT ENGINE MOUNTING BRACKET

C129225
  1. Install the bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }


9. INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY

C127255
  1. Connect the 2 cable ends with the 2 washers and 2 clips.

  1. Install 2 new clips to the control cable bracket.


10. INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY
  1. for 1AZ-FE:
    Install the clutch release cylinder (Click here).

  1. for 2AZ-FE:
    Install the clutch release cylinder (Click here).


11. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
  1. Install the back-up light switch and gasket to the transaxle case.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }

  1. D026905E01
    Connect the back-up light switch connector.


12. INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE
  1. for 1AZ-FE:
    Install the engine with manual transaxle (Click here).

  1. for 2AZ-FE:
    Install the engine with manual transaxle (Click here).


13. INSTALL STARTER ASSEMBLY (for 1AZ-FE)
  1. Install the starter (Click here).


14. INSTALL STARTER ASSEMBLY (for 2AZ-FE)
  1. for 1.6 kW Type:
    Install the starter (Click here).

  1. for 1.7 kW Type:
    Install the starter (Click here).


15. ADD TRANSAXLE OIL

16. INSPECT TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transaxle filler plug and gasket.

  1. D025304E21
    Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transaxle oil.

    Oil grade:
    GL-4

    Viscosity:
    SAE 75W

    Standard capacity:
    2.5 liters (2.6 US qts, 2.2 Imp. qts)

    NOTICE:
    1. Too much or too little oil will lead to transaxle problems.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transaxle filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


17. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
← REMOVAL (from Aug 2007)INSTALLATION (Jan 2007 – Jul 2007) →