w/o Stud Bolt: Install the cooler compressor with the 4 bolts.
Torque:
24.5 N*m{
250 kgf*cm
, 18 ft.*lbf
}
NOTICE:
Tighten the bolts in the order shown in the illustration to install the cooler compressor.
w/ Stud Bolt: Install the cooler compressor with the 3 bolts and nut.
Torque:
24.5 N*m{
250 kgf*cm
, 18 ft.*lbf
}
NOTICE:
Tighten the bolts in the order shown in the illustration to install the cooler compressor.
Connect the connector.
28.
INSTALL GENERATOR ASSEMBLY
Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.
Install the generator with the 2 bolts.
Torque:
21 N*m{
215 kgf*cm
, 16 ft.*lbf
}
for bolt A
52 N*m{
530 kgf*cm
, 38 ft.*lbf
}
for bolt B
Install the wire harness clamp.
Install the wire harness clamp bracket with the bolt.
Torque:
8.4 N*m{
85 kgf*cm
, 74 in.*lbf
}
Connect the generator wire with the nut.
Torque:
9.8 N*m{
100 kgf*cm
, 7 ft.*lbf
}
Install the terminal cap.
Connect the generator connector.
29.
INSTALL FAN AND GENERATOR V BELT
Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the fan and generator V belt.
SST
09216-42010
NOTICE:
Be sure to connect SST and the tools so that they are in line during use.
When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
After the tensioner is fully retracted, do not apply force any more than necessary.
30.
INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH
Install the clutch release cylinder for E352 (2WD) (Click here).
Install the clutch release cylinder for E359F (4WD) (Click here).
32.
INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY (for Manual Transaxle)
Install the transaxle control cable for E352 (2WD) (Click here).
Install the transaxle control cable for E359F (4WD) (Click here).
33.
INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY (for Automatic Transaxle)
Install the transaxle control cable for U241E (2WD) (Click here).
Install the transaxle control cable for U140F (4WD) (Click here).
34.
INSTALL INTAKE MANIFOLD INSULATOR
Install the intake manifold insulator onto the cylinder block.
35.
INSTALL INTAKE MANIFOLD
Install a new gasket into the intake manifold.
Install the intake manifold with the 5 bolts and 2 nuts.
Torque:
30 N*m{
305 kgf*cm
, 22 ft.*lbf
}
Fit the union to check valve hose into the vacuum hose clamp.
Install the wire harness clamp.
Connect the camshaft timing oil control valve connector.
Connect the union to check valve hose to the brake booster.
36.
INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
Install 4 new insulators into the cylinder head.
Install the 2 delivery pipe spacers onto the cylinder head.
Install the fuel delivery pipe together with the 4 fuel injectors, then temporarily tighten the 2 bolts.
NOTICE:
Be careful not to drop the fuel injectors when installing the fuel delivery pipe.
Check that the fuel injector rotates smoothly. If the fuel injector does not rotate, replace the O-ring.
Tighten the 2 bolts to the specified torque.
Torque:
20 N*m{
205 kgf*cm
, 15 ft.*lbf
}
Connect the 4 fuel injector connectors.
Install the 2 wire harness clamps.
37.
CONNECT NO. 2 VENTILATION HOSE
Connect the ventilation hose to the ventilation valve.
NOTICE:
Make sure that the paint mark and hose clamp are at the correct angle when installing the hose.
38.
INSTALL THROTTLE BODY
Install a new gasket onto the intake manifold.
Install the throttle body and fuel pipe clamp with the 4 bolts.
Torque:
30 N*m{
305 kgf*cm
, 22 ft.*lbf
}
Connect the fuel tube into the clamp.
Connect the wire harness clamp.
Connect the throttle position sensor and control motor connector.
Connect the No. 1 throttle body hose to the throttle body.
Connect the No. 2 water by-pass hose to the throttle body.
Connect the water by-pass hose to the throttle body.
Connect the purge line hose to the throttle body.
39.
CONNECT FUEL TUBE
Connect the fuel main tube.
Push the fuel tube connector until it makes a "click" sound.
Install the fuel pipe clamp.
Install the fuel tube to the fuel hose clamp.
40.
CONNECT HEATER WATER OUTLET HOSE
Connect the heater outlet hose to the heater unit.
41.
CONNECT HEATER WATER INLET HOSE
Connect the heater inlet hose to the heater unit.
42.
CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)
Connect the 2 union to connector tube hoses to the booster vacuum tube.
43.
CONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)
Connect the union to connector tube hose to the booster vacuum tube.
44.
INSTALL BATTERY CARRIER BRACKET
Install the battery carrier bracket with the nut and 2 bolts.
Torque:
20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
45.
INSTALL BATTERY BRACKET REINFORCEMENT
Install the battery bracket reinforcement with the 2 bolts.
Torque:
20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
46.
INSTALL FRONT BATTERY CARRIER
Install the front battery carrier with the 4 bolts.
Torque:
20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
Connect the 2 clamps of the engine wire.
47.
INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Connect the air cleaner case to the No. 1 air cleaner inlet.
Install the case with the 3 bolts.
Torque:
5.0 N*m{
51 kgf*cm
, 44 in.*lbf
}
48.
INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
49.
INSTALL AIR CLEANER CAP
Install the air cleaner filter element onto the air cleaner case.
Insert the hinge part of the air cleaner cap into the air cleaner case, then hang the 2 hook clamps.
Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.
NOTICE:
Make sure that the hose clamp is at the correct angle.
Connect the purge line hose to the clamp.
Connect the No. 2 ventilation hose to the air cleaner hose.
Add manual transaxle oil for E352 (2WD) (Click here).
Add manual transaxle oil for E359F (4WD) (Click here).
57.
ADD AUTOMATIC TRANSAXLE FLUID
Add automatic transaxle fluid for U241E (2WD) (Click here).
Add automatic transaxle fluid for U140F (4WD) (Click here ).
58.
CHECK FOR FUEL LEAKS
Make sure that there are no fuel leaks after performing maintenance on the fuel system.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG), and push the intelligent tester main switch ON.
NOTICE:
Do not start the engine.
Select the Active Test mode on the intelligent tester.
HINT:
Refer to the intelligent tester operator's manual for further details.
Check that there are no leaks from the fuel system.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
59.
ADD ENGINE COOLANT
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug.
Torque:
12.7 N*m{
130 kgf*cm
, 10 ft.*lbf
}
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir filler opening.
Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir's filler neck.
HINT:
The B line is the lower edge of the inner wall of the filler neck.
Standard capacity:
Item
Specified Condition
A/T
6.5 liters (6.9 US qts, 5.7 Imp. qts)
M/T
6.6 liters (7.0 US qts, 5.9 Imp. qts)
HINT:
TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
NOTICE:
Never use water as a substitute for engine coolant.
Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant. If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Start the engine and warm it up until the cooling fan operates.
Set the air conditioning as follows while warming up the engine.
Item
Specified Condition
Manual Air Conditioning System
Fan speed: Any setting except OFF Temperature: Toward WARM Air conditioning switch: OFF
Automatic Air Conditioning System
Temperature: Toward MAX Air conditioning switch: OFF
Maintain the engine speed at 2,000 to 2,500 rpm and warm up the engine until the cooling fan operates.
NOTICE:
Make sure that the radiator reservoir still has some coolant in it.
Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
If there is not enough coolant, the engine may burn out or overheat.
Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the B line.
Run the engine at 2,000 rpm until the coolant level has stabilized.
Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
CAUTION:
When pressing the radiator hoses:
Wear protective gloves.
Be careful as the radiator hoses are hot.
Keep your hands away from the radiator fan.
Stop the engine and wait until the coolant cools down to ambient temperature.
Check that the coolant level is between the FULL and LOW line. If the coolant level is below the LOW line, repeat all of the procedures above. If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.
When shifting the lever from P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.
Start the engine and make sure that the vehicle moves forward when shifting the lever from N to the D position and moves rearward when shifting the lever to the R position. If the operation cannot be performed as specified, inspect the park/neutral position switch and check the shift lever installation condition.
64.
ADJUST SHIFT LEVER POSITION
Shift the shift lever to the N position.
Slide the adjuster case cover in the direction shown in the illustration and pull out the lock piece.
Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.
Press the lock piece into the adjuster case and lock it.
Slide the cover in the direction shown in the illustration.
NOTICE:
Slide the cover past the protrusion of the lock piece.
Inspect and adjust the front wheel alignment (Click here).
73.
RESET MEMORY (for Automatic Transaxle)
When replacing the engine assembly, perform the RESET MEMORY procedure (A/T initialization ) for U241E (2WD) (Click here) and for U140F (4WD) (Click here).