2005-2008 RAV4 · Service Manual BODY

B2341 Sensor (Motor) Failure

Diagnostic trouble codes · Vehicles built from Aug 2008

Also covers:

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

When the sliding roof drive gear (sliding roof ECU) detects the motor's malfunction, and the sliding roof operation is stopped, DTC B2341 is output. When the sliding roof drive gear (sliding roof ECU) detects the gear's malfunction, and the sliding roof operation is stopped, DTC B2344 is output.
DTC Code
DTC Detection Condition
Trouble Area
B2341
Sensor (motor) Failure
  1. Sliding roof drive gear sub-assembly (sliding roof ECU)
  2. Overhead junction block (sliding roof control switch)
  3. Wire harness
B2344
Position Failure
  1. Sliding roof drive gear sub-assembly (sliding roof ECU)
  2. Overhead junction block (sliding roof control switch)
  3. Wire harness

WIRING DIAGRAM

B141540E02

INSPECTION PROCEDURE


1. CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the SLIDE OPEN and TILT UP switch (Click here).

    OK:
    Auto operation operates normally with SLIDE OPEN and TILT UP switch.



NG
Go to step 3
OK


2. DELETE DTC
  1. Delete the DTC (Click here).


NEXT

END

3. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
  1. Check that the sliding roof drive gear can be initialized (Click here).

    OK:
    Sliding roof drive gear can be initialized.



NG
Go to step 6
OK


4. CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the SLIDE OPEN and TILT UP switch (Click here).

    OK:
    Auto operation operates normally with SLIDE OPEN and TILT UP switch.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
OK


5. DELETE DTC
  1. Delete the DTC (Click here).


NEXT

END

6. CHECK WIRE HARNESS (SLIDING ROOF DRIVE GEAR - OVERHEAD JUNCTION BLOCK)

  1. B130118E07
    Disconnect the R9 ECU connector.

  1. Disconnect the R8 junction block connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    R9-7 (DWN) - R8-9 (DOWN)
    Below 1 Ω
    R9-9 (UP) - R8-8 (UP)
    Below 1 Ω
    R8-7 (GND) - Body ground
    Below 1 Ω
    R9-7 (DWN) - Body ground
    10 kΩ or higher
    R9-9 (UP) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7. INSPECT OVERHEAD JUNCTION BLOCK (SLIDING ROOF CONTROL SWITCH)

  1. E164298E01
    Remove the overhead junction block.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    8 (UP) - 7 (GND)
    TILT UP switch pushed
    Below 1 Ω
    8 (UP) - 7 (GND)
    TILT UP switch not pushed
    10 kΩ or higher
    9 (DOWN) - 7 (GND)
    SLIDE OPEN switch pushed
    Below 1 Ω
    9 (DOWN) - 7 (GND)
    SLIDE OPEN switch not pushed
    10 kΩ or higher



NG
REPLACE OVERHEAD JUNCTION BLOCK (SLIDING ROOF CONTROL SWITCH)
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)


← B2341 Sensor (Motor) Failure (+ B2344) (Nov 2005 – Jul 2008)B2342 Switch Failure (Nov 2005 – Jul 2008) →