2005-2008 RAV4 · Service Manual BODY

B2342 Switch Failure

Diagnostic trouble codes · Vehicles built Nov 2005 – Jul 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

This DTC is output when the sliding roof drive gear (sliding roof ECU) detects that the SLIDE OPEN or TILT UP switch in the overhead junction block is stuck for 30 seconds or more.
DTC No.
DTC Detection Condition
Trouble Area
B2342
Sliding roof drive gear (sliding roof ECU) detects SLIDE OPEN or TILT UP switch in overhead junction block is stuck for 30 seconds or more
  1. Sliding roof drive gear sub-assembly (sliding roof ECU)
  2. Overhead junction block (sliding roof control switch)
  3. Wire harness

WIRING DIAGRAM

Refer to DTC B2341 (Click here).

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (SLIDE OPEN AND TILT UP SWITCH)
  1. Use the Data List to check if the sliding roof control switch is functioning properly.

    Sliding roof drive gear:
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Open Switch Failure (Current)
    SLIDE OPEN switch condition (current) / Fail or Not Fail
    Fail: SLIDE OPEN switch is stuck
    Not Fail: SLIDE OPEN switch is not stuck
    -
    Close Switch Failure (Current)
    TILT UP switch condition (current) / Fail or Not Fail
    Fail: TILT UP switch is stuck
    Not Fail: SLIDE OPEN switch is not stuck
    -
    Open Switch Failure (Past)
    SLIDE OPEN switch condition (past) / Fail or Not Fail
    Fail: SLIDE OPEN switch was stuck in past
    Not Fail: SLIDE OPEN switch was not stuck in past
    -
    Close Switch Failure (past)
    TILT UP switch condition (past) / Fail or Not Fail
    Fail: TILT UP switch was stuck in past
    Not Fail: TILT UP switch was not stuck in past
    -
    OK:
    "Not Fail" appears on tester screen.



NG
Go to step 4
OK


2. CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the SLIDE OPEN and TILT UP switch (Click here).

    OK:
    Auto operation operates normally with SLIDE OPEN and TILT UP switch.



NG
Go to step 5
OK


3. DELETE DTC
  1. Delete the DTC (Click here).


NEXT

END

4. INSPECT OVERHEAD JUNCTION BLOCK (SLIDING ROOF CONTROL SWITCH)

  1. B141536E02
    Remove the overhead junction block.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tenter Connection
    Condition
    Specified Condition
    8 (UP) - 7 (GND)
    TILT UP switch pushed
    Below 1 Ω
    8 (UP) - 7 (GND)
    TILT UP switch not pushed
    10 kΩ or higher
    9 (DOWN) - 7 (GND)
    SLIDE OPEN switch pushed
    Below 1 Ω
    9 (DOWN) - 7 (GND)
    SLIDE OPEN switch not pushed
    10 kΩ or higher



OK
Go to step 10
NG


5. REPLACE OVERHEAD JUNCTION BLOCK (SLIDING ROOF CONTROL SWITCH)
  1. Temporarily replace the overhead junction block (sliding roof control switch) with a new or normally functioning one (Click here).


NEXT


6. DELETE DTC
  1. Delete the DTC (Click here).


NEXT

END

7. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
  1. Check that the sliding roof drive gear can be initialized (Click here).

    OK:
    Sliding roof drive gear can be initialized.



NG
Go to step 10
OK


8. CHECK SLIDING ROOF FUNCTION
  1. Check the auto operation with the SLIDE OPEN and TILT OPEN switch (Click here).

    OK:
    Auto operation operates normally with SLIDE OPEN and TILT UP switch.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
OK


9. DELETE DTC
  1. Delete the DTC (Click here).


NEXT

END

10. CHECK WIRE HARNESS (SLIDING ROOF DRIVE GEAR - OVERHEAD JUNCTION BLOCK)

  1. B130118E08
    Disconnect the R9 ECU connector.

  1. Disconnect the R8 junction block connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    R9-7 (DWN) - R8-9 (DOWN)
    Below 1 Ω
    R9-9 (UP) - R8-8 (UP)
    Below 1 Ω
    R8-7 (GND) - Body ground
    Below 1 Ω
    R8-9 (DOWN) - Body ground
    10 kΩ or higher
    R8-8 (UP) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)


← B2341 Sensor (Motor) Failure (+ B2344) (from Aug 2008)B2342 Switch Failure (from Aug 2008) →