Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P0617    Starter Relay Circuit High

for Preparation Click here


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

P0617 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more
Conditions (a), (b) and (c) are met for 20 seconds
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
(1 trip detection logic)
  1. Starter relay circuit
  2. Clutch start switch

Related Data List 
DTC No.
Data List
P0617
Starter Signal

WIRING DIAGRAM


A210067E01


A210068E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to the Problem Symptoms Table (Click here).
  2. If this DTC is output, inspect the starter.

1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
  1. Confirm the entry and start system.

    Result 
    Result
    Proceed to
    w/o Entry and Start System
    A
    w/ Entry and Start System
    B



B
Go to step 7
A


2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to ON and engine start.

    OK:
    Ignition Switch Condition
    Starter Signal
    ON
    OFF
    Engine Start
    ON



OK
Go to step 17

NG
Go to step 3

3.INSPECT IGNITION SWITCH


    B119736E11
  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All terminals
    Off
    10 kΩ or higher
    2 (AM1) - 1 (ST1)
    START
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Ignition Switch Assembly)
    Result 
    Result
    Proceed to
    OK (for RHD)
    A
    OK (for LHD)
    B
    NG
    C

  1. Reconnect the ignition switch assembly connector.



B
Go to step 5

C
Go to step 14
A


4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY)


    A212398E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 1 or E5-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Switch Assembly)
    *2
    No. 8 Relay Block
    *3
    ST Relay

  1. Reinstall the ST relay.

  1. Reconnect the ignition switch assembly connector.



OK
Go to step 6

NG
Go to step 16

5.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY)


    A212397E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ST Relay terminal 1 or E5-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Switch Assembly)
    *2
    No. 7 Relay Block
    *3
    ST Relay

  1. Reinstall the ST relay.

  1. Reconnect the ignition switch assembly connector.



NG
Go to step 16
OK


Go to step 7

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ECM)


    A210069E02
  1. Disconnect the ECM connector.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E5-1 (ST1) or A12-43 (STA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Switch Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the ignition switch assembly connector.



OK
Go to step 13

NG
Go to step 16

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to ON.

    OK:
    Switch Condition
    Starter Signal
    Ignition switch ON
    OFF



OK
Go to step 17

NG
Go to step 8

8.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - MAIN BODY ECU)


    A210070E01
  1. Disconnect the clutch pedal switch assembly connector.

  1. Disconnect the main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A4-2 or E20-3 (STR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch)
    *2
    Front view of wire harness connector
    (to Power Main Body ECU)
    Result 
    Result
    Proceed to
    OK (for RHD)
    A
    OK (for LHD)
    B
    NG
    C

  1. Reconnect the clutch pedal switch assembly connector.

  1. Reconnect the main body ECU connector.



B
Go to step 10

C
Go to step 16
A


9.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)


    A210071E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the clutch pedal switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 1 or A4-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch)
    *2
    No. 8 Relay Block
    *3
    ST Relay

  1. Reinstall the ST relay.

  1. Reconnect the clutch pedal switch assembly connector.



OK
Go to step 11

NG
Go to step 16

10.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)
A210072E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the clutch pedal switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ST Relay terminal 1 or A4-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch)
    *2
    No. 7 Relay Block
    *3
    ST Relay

  1. Reinstall the ST relay.

  1. Reconnect the clutch pedal switch assembly connector.



NG
Go to step 16
OK


11.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ECM)


    A168714E24
  1. Disconnect the ECM connector.

  1. Disconnect the clutch pedal switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-43 (STA) or A4-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reinstall the ECM connector.

  1. Reconnect the clutch pedal switch assembly connector.



NG
Go to step 16
OK


12.INSPECT CLUTCH PEDAL SWITCH ASSEMBLY
  1. Inspect the clutch pedal switch assembly (Click here).



NG
Go to step 15
OK


13.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 17

14.REPLACE IGNITION SWITCH ASSEMBLY
  1. Replace the ignition switch assembly (Click here).



NEXT
Go to step 17

15.REPLACE CLUTCH PEDAL SWITCH ASSEMBLY
  1. Replace the clutch pedal switch assembly (Click here).



NEXT
Go to step 17

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


17.CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON.

  1. Drive vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.

  1. Confirm that the DTC is not output again.


NEXT

END