Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the coil of the ST relay, while at the same time, a signal is sent to terminal STA of the ECM.

WIRING DIAGRAM


A210606E04


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
This troubleshooting procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table (Click here).

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value.

    OK:
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT ST RELAY
  1. Inspect the ST relay (Click here).
    Result 
    Result
    Proceed to
    OK (for Manual Transaxle)
    A
    OK (for Automatic Transaxle)
    B
    NG
    C



B
Go to step 8

C
REPLACE ST RELAY
A


3.INSPECT IGNITION SWITCH


    B119736E11
  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All terminals
    Off
    10 kΩ or higher
    2 (AM1) - 1 (ST1)
    START
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Ignition Switch Assembly)
    Result 
    Result
    Proceed to
    OK (for RHD)
    A
    OK (for LHD)
    B
    NG
    C

  1. Reconnect the ignition switch assembly connector.



B
Go to step 6

C
REPLACE IGNITION SWITCH (Click here)
A


4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ST RELAY)


    A212398E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - E5-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or E5-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Switch Assembly)
    *2
    No. 8 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)


    A212400E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - A12-43 (STA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or A12-43 (STA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    *2
    No. 8 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ST RELAY)
A212397E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - E5-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or E5-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Switch Assembly)
    *2
    No. 7 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
A212399E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - A12-43 (STA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or A12-43 (STA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    *2
    No. 7 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

8.INSPECT IGNITION SWITCH


    B119736E11
  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All terminals
    Off
    10 kΩ or higher
    2 (AM1) - 1 (ST1)
    START
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Ignition Switch Assembly)

  1. Reconnect the ignition switch assembly connector.



NG
REPLACE IGNITION SWITCH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)


    A210601E03
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E5-1 (ST1) - B28-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E5-1 (ST1) or B28-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    Front view of wire harness connector
    (to Ignition Switch)
    Result 
    Result
    Proceed to
    OK (for RHD)
    A
    OK (for LHD)
    B
    NG
    C

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the ignition switch assembly connector.



B
Go to step 12

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)


    A206054E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - B28-9
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or B28-9 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    No. 8 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)


    A212400E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - A12-43 (STA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or A12-43 (STA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    *2
    No. 8 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the ECM connector.



OK
Go to step 14

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)


    A206055E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - B28-9
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or B28-9 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    No. 7 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
A212399E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - A12-43 (STA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or A12-43 (STA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)
    *2
    No. 7 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly .



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    A208658E04
  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A12-43 (STA) - B28-9
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A12-43 (STA) or B28-9 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)