Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P2714    Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)

for Preparation Click here


DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The TCM adjusts the duty ratio* of shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

HINT:
*: The duty ratio is the ratio of the electrical current on time (A) to the total of the electrical current on and off time (A + B).
Duty Ratio (%) = (A / (A + B)) x 100


C206300E01


DTC Code
DTC Detection Condition
Trouble Area
P2714
The TCM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in the speed between the turbine and output shaft, and also by the ATF pressure. (2-trip detection logic)
  1. Shift solenoid valve SLT remains open
  2. Shift solenoid valve SL1, SL2, SL3 or SL4 remains open or closed
  3. Valve body is blocked
  4. Automatic transaxle (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

The TCM calculates the amount of heat absorbed by the friction material based on the difference in revolution speed (clutch slippage) between the turbine and output shaft. The TCM turns on the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.
When shift solenoid valve SLT remains on, the line pressure goes down and clutch engagement force decreases.

NOTICE:
If driving continues under these conditions, clutches will burn out and the vehicle will no longer be drivable.


INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2714)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / DTC.

  1. Read the DTCs using the intelligent tester.
    Result 
    Result
    Proceed to
    P2714 and other DTCs are output
    A
    Only P2714 is output
    B

    HINT:
    If shift solenoid valve SLT is stuck on, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.



B
Go to step 4
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test while the ATF temperature is 50 to 80°C (122 to 176°F)
  2. Be careful to prevent the hose of SST from interfering with the exhaust pipe.
  3. This check must be conducted after checking and confirming that the engine is normal.
  4. Perform the test with the A/C off.

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C205628E01
  1. Remove the test plug from the transaxle case and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure when the engine is idling.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the tester, perform the Active Test.

  1. Measure the line pressure with SST.

    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    ON: No action (normal operation)
    OFF: Line pressure up (When Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn off).

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: The "Activate the Solenoid (SLT)" Active Test is performed to confirm that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (Click here).
    Note that the pressure readings for the Active Test and Hydraulic Test are different.

    OK:
    The line pressure changes as specified when performing the Active Test.



NG
Go to step 6
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)

NOTICE:
This test should always be performed with at least 2 people.

  1. Warm up the engine.

  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    HINT:
    Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem (Click here).


    ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate the shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Can be used to check the operation of the shift solenoid valves.
    A 10-second interval is required between gear changes.
    Do not down-shift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    1. 50 km/h (30 mph) or less

    NOTICE:
    1. This test can be conducted when the vehicle is stopped.
    2. When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.

    HINT:
    The gear commanded by the TCM is shown in the Data List / Shift Status display on the intelligent tester.

  1. Check the vehicle speed and gear when the engine speed is 1000 rpm.

    HINT:
    Because the torque converter clutch has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th and 6th gear, however a difference of speed should still be evident following each gear change.


    Standard 
    1st
    2nd
    3rd
    4th
    5th
    6th
    8 to 12 km/h (5 to 7.5 mph)
    15 to 19 km/h (9.3 to 11.8 mph)
    21 to 25 km/h (13.0 to 15.5 mph)
    31 to 35 km/h (19.3 to 21.7 mph)
    44 to 48 km/h (27.3 to 29.8 mph)
    52 to 56 km/h (32.3 to 34.8 mph)

  1. Compare the TCM commanded gear and the actual gear.

    Result:

    System Condition
    TCM Gear Shift Command
    Proceed to
    1st
    2nd
    3rd
    4th
    5th
    6th
    Malfunction
    Shift solenoid valve SL1
    Stuck ON
    1st
    2nd
    3rd
    4th
    4th
    4th
    A
    Stuck OFF
    N*1
    N*1
    N*1
    N*1
    5th
    6th
    Shift solenoid valve SL2
    Stuck ON
    4th
    4th
    4th
    4th
    5th
    6th
    B
    Stuck OFF
    1st
    2nd
    3rd
    1st
    N*1
    N*1
    Shift solenoid valve SL3
    Stuck ON
    2nd
    2nd
    3rd
    4th
    5th
    6th
    C
    Stuck OFF
    1st
    1st
    3rd
    4th
    5th
    N*1
    Shift solenoid valve SL4
    Stuck ON
    3rd
    3rd
    3rd
    4th
    5th
    5th
    D
    Stuck OFF
    1st
    2nd
    1st
    4th
    N*1
    6th
    Shift solenoid valve SLT
    Stuck ON
    N*2
    N*2
    N*2
    N*2
    N*2
    N*2
    E
    Stuck OFF*3
    1st
    2nd
    3rd
    4th
    5th
    6th

    HINT:
    1. *1: Neutral
    2. *2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
    3. *3: When shift solenoid valve SLT is stuck off, gear shifting is normal.



B
GO TO DTC P0776 (Click here)

C
GO TO DTC P0796 (Click here)

D
GO TO DTC P2808 (Click here)

E
Go to step 8
A

GO TO DTC P0746 (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SLT


    C197715E05
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)  

6.INSPECT SHIFT SOLENOID VALVE SLT


    C197715E05
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


7.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)  

8.INSPECT SHIFT SOLENOID VALVE SLT


    C197715E05
  1. Remove shift solenoid valve SLT.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes an operating noise

Text in Illustration 
*1
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


9.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)