DTC P0796 Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0796 | Either condition is met (2-trip detection logic):
|
|
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0796) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / DTC.
Read the DTCs using the intelligent tester.
| Result | Proceed to |
| P0796 and other DTCs are output | A |
| Only P0796 is output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST) |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate the shift solenoid valves and set each shift position |
| Can be used to check the operation of the shift solenoid valves. A 10-second interval is required between gear changes. Do not down-shift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition]
|
Check the vehicle speed and gear when the engine speed is 1000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM commanded gear and the actual gear.
| System Condition | TCM Gear Shift Command | Proceed to | |||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | ||||
| Malfunction | Shift solenoid valve SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | |||
| Shift solenoid valve SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B | |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | |||
| Shift solenoid valve SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C | |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | |||
| Shift solenoid valve SL4 | Stuck ON | 3rd | 3rd | 3rd | 4th | 5th | 5th | D | |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | |||
| Shift solenoid valve SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E | |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | |||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 3.INSPECT SHIFT SOLENOID VALVE SL3 |
![]() |
Remove shift solenoid valve SL3.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
| Valve moves and makes an operating noise |
| *1 | Component without harness connected (Shift Solenoid Valve SL3) |
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||
| 5.INSPECT SHIFT SOLENOID VALVE SL3 |
![]() |
Remove shift solenoid valve SL3.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
| Valve moves and makes an operating noise |
| *1 | Component without harness connected (Shift Solenoid Valve SL3) |
|
| ||||
| OK | |
| 6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||