Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > Cranking Holding Function Circuit

for Preparation Click here


DESCRIPTION

The cranking holding control system provides current to the starter when the ECM detects the engine switch start signal (STSW). When the ECM receives the STSW signal, it turns on the ACC CUT relay, which prevents flickering of the combination meter, clock, audio system, etc. Also, the ECM sends a signal from its STAR terminal which travels through the clutch pedal switch assembly*1 or park/neutral position switch*2 to the ST relay, causing the starter to activate. When the engine is cranking, the starter operation signal is sent to the STA terminal of the ECM. When the ECM determines that the engine has started, the system cuts current to the starter.
  1. *1: for Manual Transaxle
  2. *2: for Automatic Transaxle

A103821E60


WIRING DIAGRAM


A210089E04


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.CHECK CRANKING
  1. Check the cranking of the engine.
    Result 
    Result
    Proceed to
    Cranking possible and holding control operates
    A
    Does not crank
    B
    Cranking possible but holding control does not operate
    C



B
Go to step 2

C
Go to step 18
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Check the result when the engine switch is turned on (IG) and when the engine is cranking.

    OK:
    Engine Switch Condition
    Display (Starter Signal)
    On (IG)
    OFF
    Start
    ON



NG
Go to step 11
OK


3.INSPECT STARTER RELAY (ST)
  1. Inspect the starter relay (ST) (Click here).
    Result 
    Result
    Proceed to
    OK (for RHD)
    A
    OK (for LHD)
    B
    NG
    C



B
Go to step 7

C
REPLACE STARTER RELAY (ST)
A


4.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A210274E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2 (ST relay holder) - 5 (ST relay holder)
    Always
    11 to 14 V

    Result 
    Result
    Proceed to
    OK (for Manual Transaxle)
    A
    OK (for Automatic Transaxle)
    B
    NG
    C
    Text in Illustration 
    *1
    No. 8 Relay Block
    *2
    ST Relay Holder

  1. Reinstall the ST relay.



B
Go to step 6

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BATTERY, BODY GROUND)
A


5.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)
A210071E01
  1. Disconnect the clutch pedal switch assembly connector.

  1. Remove the ST relay from the No. 8 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - A4-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or A4-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch Assembly)
    *2
    No. 8 Relay Block
    *3
    ST Relay Holder

  1. Reconnect the clutch pedal switch assembly connector.

  1. Reinstall the ST relay.



OK
Go to step 10

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)


    A206054E01
  1. Remove the ST relay from the No. 8 relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - B28-9
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or B28-9 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    No. 8 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the park/neutral position switch connector.



OK
Go to step 10

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A210275E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2 (ST relay holder) - 5 (ST relay holder)
    Always
    11 to 14 V

    Result 
    Result
    Proceed to
    OK (for Manual Transaxle)
    A
    OK (for Automatic Transaxle)
    B
    NG
    C
    Text in Illustration 
    *1
    No. 7 Relay Block
    *2
    ST Relay Holder

  1. Reinstall the ST relay.



B
Go to step 9

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER RELAY (ST) - BATTERY, BODY GROUND)
A


8.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)
A210072E01
  1. Disconnect the clutch pedal switch assembly connector.

  1. Remove the ST relay from the No. 7 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - A4-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or A4-1 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch Assembly)
    *2
    No. 7 Relay Block
    *3
    ST Relay Holder

  1. Reconnect the clutch pedal switch assembly connector.

  1. Reinstall the ST relay.



OK
Go to step 10

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)


    A206055E01
  1. Remove the ST relay from the No. 7 relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) - B28-9
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1 (ST relay holder) or B28-9 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    No. 7 Relay Block
    *3
    ST Relay Holder

  1. Reinstall the ST relay.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.INSPECT STARTER
  1. Inspect the starter (Click here).
    Result 
    Result
    Proceed to
    OK
    A
    NG
    B



B
REPLACE STARTER (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR (STARTER - STARTER RELAY (ST), BATTERY) 

11.INSPECT STARTER CUT RELAY (ST CUT)
  1. Inspect the starter cut relay (ST CUT) (Click here).
    Result 
    Result
    Proceed to
    OK (for Manual Transaxle)
    A
    OK (for Automatic Transaxle)
    B
    NG
    C



B
Go to step 15

C
REPLACE STARTER CUT RELAY (ST CUT)
A


12.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - CLUTCH PEDAL SWITCH ASSEMBLY, MAIN BODY ECU AND ECM)
A130165E03
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Disconnect the clutch pedal switch assembly connector.

  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) - B32-39 (STAR)
    Always
    Below 1 Ω
    3 (ST CUT relay holder) - E20-14 (STR2)
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - A4-2
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - E20-3 (STR)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) or B32-39 (STAR) - Body ground
    Always
    10 kΩ or higher
    3 (ST CUT relay holder) or E20-14 (STR2) - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or A4-2 - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or E20-3 (STR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    No. 7 Relay Block
    *2
    ST CUT Relay Holder
    *3
    Front view of wire harness connector
    (to Clutch Pedal Switch Assembly)
    *4
    Front view of wire harness connector
    (to Main Body ECU)
    *5
    Front view of wire harness connector
    (to ECM)

  1. Reinstall the ST CUT relay.

  1. Reconnect the clutch pedal switch assembly connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.INSPECT CLUTCH PEDAL SWITCH ASSEMBLY
  1. Inspect the clutch pedal switch assembly (Click here).



NG
REPLACE CLUTCH PEDAL SWITCH ASSEMBLY (Click here)
OK


14.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ECM)
A168714E24
  1. Disconnect the clutch pedal switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A4-1 - A12-43 (STA)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A4-1 or A12-43 (STA) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Clutch Pedal Switch Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the clutch pedal switch assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

15.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - PARK/NEUTRAL POSITION SWITCH, MAIN BODY ECU AND ECM)
A206056E01
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) - B32-39 (STAR)
    Always
    Below 1 Ω
    3 (ST CUT relay holder) - E20-14 (STR2)
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - B28-4
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - E20-3 (STR)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) or B32-39 (STAR) - Body ground
    Always
    10 kΩ or higher
    3 (ST CUT relay holder) or E20-14 (STR2) - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or B28-4 - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or E20-3 (STR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    No. 7 Relay Block
    *2
    ST CUT Relay Holder
    *3
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *4
    Front view of wire harness connector
    (to Main Body ECU)
    *5
    Front view of wire harness connector
    (to ECM)

  1. Reinstall the ST CUT relay.

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly .



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    A208658E04
  1. Disconnect the ECM connector.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A12-43 (STA) - B28-9
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A12-43 (STA) or B28-9 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
A127899E16
  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    E20-4 (STSW) - A12-19 (STSW)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    E20-4 (STSW) or A12-19 (STSW) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for Manual Transaxle)
    A
    OK (for Automatic Transaxle)
    B
    NG
    C
    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Main Body ECU)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



B
Go to step 20

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


19.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - CLUTCH PEDAL SWITCH ASSEMBLY, MAIN BODY ECU AND ECM)
A130165E03
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Disconnect the clutch pedal switch assembly connector.

  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) - B32-39 (STAR)
    Always
    Below 1 Ω
    3 (ST CUT relay holder) - E20-14 (STR2)
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - A4-2
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - E20-3 (STR)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) or B32-39 (STAR) - Body ground
    Always
    10 kΩ or higher
    3 (ST CUT relay holder) or E20-14 (STR2) - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or A4-2 - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or E20-3 (STR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    No. 7 Relay Block
    *2
    ST CUT Relay Holder
    *3
    Front view of wire harness connector
    (to Clutch Pedal Switch Assembly)
    *4
    Front view of wire harness connector
    (to Main Body ECU)
    *5
    Front view of wire harness connector
    (to ECM)

  1. Reinstall the ST CUT relay.

  1. Reconnect the clutch pedal switch assembly connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

20.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - PARK/NEUTRAL POSITION SWITCH, MAIN BODY ECU AND ECM)
A206056E01
  1. Remove the ST CUT relay from the No. 7 relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the main body ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) - B32-39 (STAR)
    Always
    Below 1 Ω
    3 (ST CUT relay holder) - E20-14 (STR2)
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - B28-4
    Always
    Below 1 Ω
    5 (ST CUT relay holder) - E20-3 (STR)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    3 (ST CUT relay holder) or B32-39 (STAR) - Body ground
    Always
    10 kΩ or higher
    3 (ST CUT relay holder) or E20-14 (STR2) - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or B28-4 - Body ground
    Always
    10 kΩ or higher
    5 (ST CUT relay holder) or E20-3 (STR) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    No. 7 Relay Block
    *2
    ST CUT Relay Holder
    *3
    Front view of wire harness connector
    (to Park/Neutral Position Switch)
    *4
    Front view of wire harness connector
    (to Main Body ECU)
    *5
    Front view of wire harness connector
    (to ECM)

  1. Reinstall the ST CUT relay.

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the main body ECU connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)