DTC C1413 Front Speed Sensor RH Output Malfunction |
DTC C1414 Front Speed Sensor LH Output Malfunction |

| DTC Code | DTC Detection Condition | Trouble Area |
| C1413 C1414 | Any of the following is detected:
|
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Speed Open | FR speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| FL Speed Open | FL speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| FR Wheel Speed | FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) | Actual wheel speed | Similar to speed indicated on the speedometer. |
| FL Wheel Speed | FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) | Actual wheel speed | Similar to speed indicated on the speedometer. |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs (C1413 and C1414) are not output. | A |
| DTCs (C1413 and/or C1414) are output. | B |
|
| ||||
| A | ||
| ||
| 4.CHECK FRONT SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 5.CHECK FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
|
| ||||
| OK | |
| 6.CHECK FRONT SPEED SENSOR ROTOR |
Remove the front axle hub sub-assembly (Click here).
Check the speed sensor rotor.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
![]() |
Install the front speed sensor and the front speed sensor rotor.
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the skid control ECU connector and the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A67-7 (FR+) - A62-1 | Always | Below 1 Ω |
| A67-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| A67-6 (FR-) - A62-2 | Always | Below 1 Ω |
| A67-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A67-19 (FL+) - A61-1 | Always | Below 1 Ω |
| A67-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A67-18 (FL-) - A61-2 | Always | Below 1 Ω |
| A67-18 (FL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT SKID CONTROL ECU (SENSOR INPUT) |
![]() |
Reconnect the skid control ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A62-1 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| A61-1 - Body ground | Ignition switch ON | 8 to 14 V |
|
| ||||
| OK | ||
| ||