Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.
There is little variation in the output from the mass air flow meter, as the output voltage is converted into a periodic signal which minimizes the effect of wire harness resistance.
The internal circuit of the mass air flow meter contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 250 to 11000 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A207644E01


P0102 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After engine is started for 3 seconds
MAF meter frequency is less than 85 Hz with the engine speed at 5000 rpm or less for 3 seconds.
(1 trip detection logic)
  1. Open or short in Mass Air Flow (MAF) meter circuit
  2. Mass air flow meter
  3. ECM

P0103 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After engine is started for 3 seconds
MAF meter frequency is more than 9800 Hz with the engine speed at 5000 rpm or less for 3 seconds.
(1 trip detection logic)
  1. Open or short in Mass Air Flow (MAF) meter circuit
  2. Mass air flow meter
  3. ECM

Related Data List 
DTC No.
Data List
P0102
MAF
P0103

HINT:
  1. If DTC P0102 is stored, the following symptoms may appear (as the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):
    1. Combustion noise worsens
  2. If DTC P0103 is stored, the following symptoms may appear (as the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased according to the target EGR):
    1. Misfire
    2. White smoke
    3. Black smoke


WIRING DIAGRAM


A204468E02


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
A127724E51
  1. Disconnect the mass air flow meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B1-3 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Mass Air Flow Meter)

  1. Reconnect the mass air flow meter connector.



NG
Go to step 3
OK


2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    A204469E05
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B1-1 (VG) - B32-65 (VG)
    Always
    Below 1 Ω
    B1-2 (E2G) - B32-64 (EVG)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B1-1 (VG) or B32-65 (VG) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Mass Air Flow Meter)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



OK
Go to step 6

NG
Go to step 4

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)


    A127960E05
  1. Disconnect the mass air flow meter connector.

  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B1-3 (+B) - 1A-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B1-3 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Mass Air Flow Meter)
    *2
    Engine Room No. 1 Relay Block
    *3
    Front view of wire harness connector
    (to Integration Relay)

  1. Reconnect the mass air flow meter connector.

  1. Reinstall the integration relay.



OK
Go to step 5

NG
Go to step 4

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 9

5.CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NEXT
Go to step 9

6.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. After engine is started for 3 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P0102 or P0103
    A
    No output
    B



B
END
A


8.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Start the engine and wait for 3 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END