ECD SYSTEM (for CCo) > ECM Power Source Circuit |

| 1.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BATTERY) |
![]() |
Remove the integration relay from the engine room No. 1 relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Engine room relay block (1C-1) - Body ground | Always | 11 to 14 V |
| *1 | Engine Room No. 1 Relay Block |
| *2 | Front view of wire harness connector (to Integration Relay) |
Reinstall the integration relay.
|
| ||||
| OK | |
| 2.INSPECT INTEGRATION NO.1 RELAY (EFI MAIN RELAY) |
Inspect the EFI MAIN relay .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT) |
![]() |
Check the harness and connectors between the integration relay and ECM.
Remove the integration relay from the engine room No. 1 relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-45 (MREL) - 1A-2 | Always | Below 1 Ω |
| A12-1 (+B) - 1A-4 | Always | |
| A12-20 (+B2) - 1A-4 | Always |
| Tester Connection | Condition | Specified Condition |
| A12-45 (MREL) or 1A-2 - Body ground | Always | 10 kΩ or higher |
| A12-1 (+B) or 1A-4 - Body ground | Always | |
| A12-20 (+B2) or 1A-4 - Body ground | Always |
| *1 | Front view of wire harness connector (to ECM) |
| *2 | Engine Room No. 1 Relay Block |
| *3 | Front view of wire harness connector (to Integration Relay) |
Check the harness and connectors between the integration relay and body ground.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1A-3 - Body ground | Always | Below 1 Ω |
Reinstall the integration relay.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B32-109 (E1) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 5.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Disconnect the ECM connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A12-25 (IGSW) - B32-109 (E1) | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to ECM) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connectors.
|
| ||||
| OK | ||
| ||
| 6.INSPECT RELAY (IG2 RELAY POWER SOURCE) |
![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (IG2 relay holder) - Body ground | Always | 11 to 14 V |
| *1 | Engine Room No. 1 Relay Block |
| *2 | IG2 Relay |
|
| ||||
| OK | |
| 7.INSPECT IG2 RELAY |
![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
Reinstall the relay.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM NO. 1 RELAY BLOCK) |
![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 5 (IG2 relay holder) - A12-25 (IGSW) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 5 (IG2 relay holder) or A12-25 (IGSW) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to ECM) |
| *2 | Engine Room No. 1 Relay Block |
| *3 | IG2 Relay |
Reinstall the IG2 relay.
Reconnect the ECM connector.
| Result | Proceed to |
| OK | A |
| NG (w/ Entry and Start System) | B |
| NG (w/o Entry and Start System) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK - MAIN BODY ECU) |
![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (IG2 relay holder) - E19-5 (IG2D) | Always | Below 1 Ω |
| 2 (IG2 relay holder) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (IG2 relay holder) or E19-5 (IG2D) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Main Body ECU) |
| *2 | Engine Room No. 1 Relay Block |
| *3 | IG2 Relay |
Reinstall the IG2 relay.
Reconnect the main body ECU connector.
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK - IGNITION SWITCH) |
![]() |
Remove the IG2 relay from the engine room No. 1 relay block.
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (IG2 relay holder) - E5-6 (IG2) | Always | Below 1 Ω |
| 2 (IG2 relay holder) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 1 (IG2 relay holder) or E5-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Ignition Switch) |
| *2 | Engine Room No. 1 Relay Block |
| *3 | IG2 Relay |
Reinstall the IG2 relay.
Reconnect the ignition switch connector.
|
| ||||
| OK | |
| 11.INSPECT IGNITION SWITCH ASSEMBLY |
Inspect the ignition switch assembly (Click here).
|
| ||||
| OK | ||
| ||