Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P0405    Exhaust Gas Recirculation Sensor "A" Circuit Low

DTC    P0406    Exhaust Gas Recirculation Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.

P0405 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
EGR valve position sensor output voltage is less than 0.1 V for 5 seconds.
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve assembly (EGR valve position sensor)
  3. ECM

P0406 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 5 seconds
EGR valve position sensor output voltage is higher than 4.9 V for 5 seconds.
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve assembly (EGR valve position sensor)
  3. ECM

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

Refer to DTC P0400 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)


    A204591E06
  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    z1-2 (VC) - B32-94 (VCEG)
    Always
    Below 1 Ω
    z1-4 (VTA) - B32-118 (EGLS)
    Always
    Below 1 Ω
    z1-3 (E2) - B32-95 (EEGL)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    z1-2 (VC) or B32-94 (VCEG) - Body ground
    Always
    10 kΩ or higher
    z1-4 (VTA) or B32-118 (EGLS) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Electric EGR Valve Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the EGR valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    A204592E02
  1. Disconnect the EGR valve assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z1-2 (VC) - z1-3 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Electric EGR Valve Assembly)

  1. Reconnect the EGR valve assembly connector.



NG
Go to step 5
OK


3.REPLACE EGR VALVE ASSEMBLY
  1. Replace the EGR valve assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.

    OK:
    DTC is not output again.



NG
Go to step 5
OK

END 

5.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END