DTC P0088 Fuel Rail / System Pressure - Too High |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds | The fuel pressure of the common rail exceeds 220000 kPa (2243 kgf/cm2, 319000 psi). (1 trip detection logic) |
|
| DTC No. | Data List |
| P0088 |
|
| Engine Speed | Fuel Press |
| Idling |
|
| 3000 rpm (No engine load) |
|

| 1.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.
Read the value.
| Engine Speed | Target Pump SCV Current |
| Idling | 923 to 1123 mA |
| 2500 rpm (No engine load) | 980 to 1212 mA |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
Check the difference in pressure between Fuel Press and Target Common Rail Pressure.
|
| ||||
| OK | |
| 3.INSPECT PRESSURE DISCHARGE VALVE (COMMON RAIL) |
Inspect the pressure discharge valve .
|
| ||||
|
| ||||
| 4.REPLACE PRESSURE DISCHARGE VALVE (COMMON RAIL) |
Replace the common rail (Click here).
|
| ||||
| 5.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
![]() |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) - B32-41 (PCV+) | Always | Below 1 Ω |
| B46-2 (PCV) - B32-81 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B46-1 (+B) or B32-41 (PCV+) - Body ground | Always | 10 kΩ or higher |
| B46-2 (PCV) or B32-81 (PCV-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Suction Control Valve) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
| NEXT | |
| 7.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 8.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 9.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0088 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 10.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 11.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.
Confirm that the DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0088.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
| NEXT | ||
| ||