DTC P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state. | The throttle motor activation duty is more than specified value for 30 seconds (1 trip detection logic). |
|
| DTC No. | Data List |
| P0488 |
|
| Condition | Throttle Valve Position |
| Moment when accelerator pedal is depressed further or released at 3000 rpm | Throttle valve opening angle varies smoothly |
| Throttle Condition | Target Throttle Position | Actual Throttle Position | Throttle Close Learning Val. | Diesel Throttle Learn Status |
| Throttle Valve Fully Closed | 100% | 100% | 14.25 to 21.25 deg | OK |
| Throttle Valve Fully Open | 0% | 0% |



| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0488) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0488 | A |
| DTC P0488 and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (DIESEL THROTTLE LEARN STATUS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Throttle Learn Status.
Read the values when the ignition switch is ON.
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DIESEL THROTTLE TARGET ANGLE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle.
When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.
|
| ||||
| OK | |
| 4.REMOVE DEPOSIT (CLEAN EGR PASSAGE) |
Remove the EGR valve assembly, No. 2 intake manifold and intake manifold.
Remove the deposits from those parts and clean the parts.

Reinstall the EGR valve assembly, No. 2 intake manifold and intake manifold.
| NEXT | |
| 5.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT) |
Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.
|
| ||||
|
| ||||
| 6.REMOVE DEPOSIT (CLEAN EGR PASSAGE) |
Remove the EGR valve assembly, No. 2 intake manifold and intake manifold.
Remove the deposits from those parts and clean the parts.

Reinstall the EGR valve assembly, No. 2 intake manifold and intake manifold.
| NEXT | |
| 7.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT) |
Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (ECM - DIESEL THROTTLE BODY ASSEMBLY) |
![]() |
Disconnect the diesel throttle body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B107-5 (VC) - B32-97 (VCVL) | Always | Below 1 Ω |
| B107-6 (VTA) - B32-119 (VLU) | Always | Below 1 Ω |
| B107-3 (E2) - B32-96 (EVLU) | Always | Below 1 Ω |
| B107-2 (M+) - B32-42 (M+) | Always | Below 1 Ω |
| B107-1 (M-) - B32-43 (M-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B107-5 (VC) or B32-97 (VCVL) - Body ground | Always | 10 kΩ or higher |
| B107-6 (VTA) or B32-119 (VLU) - Body ground | Always | 10 kΩ or higher |
| B107-3 (E2) or B32-96 (EVLU) - Body ground | Always | 10 kΩ or higher |
| B107-2 (M+) or B32-42 (M+) - Body ground | Always | 10 kΩ or higher |
| B107-1 (M-) or B32-43 (M-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Throttle Body) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the diesel throttle body assembly connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 10.REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace the diesel throttle body assembly (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488) |
Start the engine and warm it up.
Connect the intelligent tester to the DLC3.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, Target Throttle Position and Actual Throttle Position.
![]() |
Take a snapshot with the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle.
When changing the Active Test value continuously to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
|
| ||||
| OK | ||
| ||
| 12.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488) |
Start the engine and warm it up.
Connect the intelligent tester to the DLC3.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, Target Throttle Position and Actual Throttle Position.
![]() |
Take a snapshot with the intelligent tester.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle.
When changing the Active Test value continuously to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||