DTC P1271 Fuel Regulator Circuit Malfunction (EDU Drive) |
DTC P1272 Fuel Pressure Regulator Malfunction |


| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON to off and Drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal | When either condition below is met (1 trip detection logic):
|
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON to off | Pressure discharge valve does not open. Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off. (2 trip detection logic) |
|
| DTC No. | Data List |
| P1271 |
|
| P1272 |
| Engine Speed | Fuel Pressure (kPa) |
| Idling | Fuel Press is within +/-5000 kPa of Target Common Rail Pressure |
| 2500 rpm (No engine load) |
| Condition | Fuel Press (Idling) | Fuel Press (1 Second after Engine Stopped) |
| Pressure discharge valve normal | 35000 kPa | 170 kPa |
| Open in pressure discharge valve circuit | 34000 kPa | 34300 kPa |

| Required sensors | EDU |
| Frequency of operation | Continuous |
| Duration | 3 seconds |
| MIL operation | 1 driving cycle |
| Required sensors | Fuel pressure sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 1 second |
| MIL operation | 2 driving cycles |
| Specification |
| The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times. |
| Item | Specification | |
| Minimum | Maximum | |
| Fuel pressure | 30000 kPa (306 kgf/cm2, 4350 psi) | - |
| Fuel temperature | 0°C (32°F) | - |
| Battery voltage | 11 V | - |
| The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning. | ||
| Specification |
| There are no confirmation signals from the EDU for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration. |
| Specification |
| The internal pressure stays beyond the specified level after the ignition switch is turned off. |

| 1.CHECK IF DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
| Result | Proceed to |
| P1272 | A |
| P1271 | B |
| P1271 and P1272 | B |
| Other DTCs output | C |
|
| ||||
|
| ||||
| A | |
| 2.INSPECT COMMON RAIL ASSEMBLY |
Inspect the common rail assembly .
|
| ||||
|
| ||||
| 3.INSPECT PRESSURE DISCHARGE VALVE |
![]() |
Disconnect the pressure discharge valve connector.
Measure the resistance according to the value(s) in the table below.
| Condition | Specified Condition |
| 20°C (68°F) | 0.85 to 1.05 Ω |
| *1 | Component without harness connected (Pressure Discharge Valve) |
Reconnect the pressure discharge valve connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - EDU) |
![]() |
Disconnect the EDU connector.
Disconnect the pressure discharge valve connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B108-2 - B105-1 (RLF+) | Always | Below 1 Ω |
| B108-1 - B105-2 (RLF-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B108-2 or B105-1 (RLF+) - Body ground | Always | 10 kΩ or higher |
| B108-1 or B105-2 (RLF-) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Pressure Discharge Valve) |
| *2 | Front view of wire harness connector (to EDU) |
Reconnect the EDU connector.
Reconnect the pressure discharge valve connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ECM - EDU) |
![]() |
Disconnect the EDU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B104-5 (PRD) - B32-52 (PRD) | Always | Below 1 Ω |
| B104-1 (RLF) - B32-123 (RLFF) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B104-5 (PRD) or B32-52 (PRD) - Body ground | Always | 10 kΩ or higher |
| B104-1 (RLF) or B32-123 (RLFF) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to EDU) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the EDU connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.INSPECT EDU (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the EDU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B102-2 (+B) - B102-4 (GND) | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Injector Driver (EDU)) |
Reconnect the EDU connector.
|
| ||||
| OK | |
| 7.REPLACE EDU |
Replace the EDU (Click here).
| NEXT | |
| 8.CHECK IF DTC OUTPUT RECURS (DTC P1271 AND/OR P1272) |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1271 and P1272.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
| Pending DTC | P1271 and/or P1272 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
|
| ||||
| A | ||
| ||
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
| ||||
| 10.GO TO INJECTOR CIRCUIT |
Go to injector circuit (Click here).
|
| ||||
| 11.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 12.REPLACE COMMON RAIL |
Replace the common rail (Click here).
| NEXT | |
| 13.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the pending DTC is not output again.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1271 and P1272.
Check the DTC judgment result.
| NEXT | ||
| ||