Home › ENGINE · 2AD-FHV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates a power supply voltage of 5 V from the battery voltage supplied to the +B and BATT terminals to operate the microprocessor. The ECM provides this power to the sensors through the VC output circuit.

A116143E68

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM


A209872E01


A209873E01


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch to ON.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
END
B


2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Check the communication between the tester and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
B


4.CHECK MIL (DIESEL THROTTLE BODY ASSEMBLY)
  1. Disconnect the diesel throttle body assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the diesel throttle body assembly connector.



A
REPLACE DIESEL THROTTLE BODY ASSEMBLY (Click here)
B


5.CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the fuel pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the fuel pressure sensor connector.



A
REPLACE COMMON RAIL ASSEMBLY (Click here)
B


6.CHECK MIL (EGR VALVE ASSEMBLY)
  1. Disconnect the EGR valve assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the EGR valve assembly connector.



A
REPLACE EGR VALVE ASSEMBLY (Click here)
B


7.CHECK MIL (DIFFERENTIAL PRESSURE SENSOR)
  1. Disconnect the differential pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the differential pressure sensor connector.



A
REPLACE DIFFERENTIAL PRESSURE SENSOR (Click here)
B


8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the manifold absolute pressure sensor connector.



A
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
B


9.CHECK MIL (BATTERY CURRENT SENSOR ASSEMBLY)
  1. Disconnect the battery current sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the battery current sensor connector.



A
REPLACE BATTERY CURRENT SENSOR ASSEMBLY
B


10.CHECK HARNESS AND CONNECTOR
  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the diesel throttle body assembly connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the differential pressure sensor connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the battery current sensor connector.



    A210591E03
  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A12-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A12-57 (VCP2) - Body ground
    Always
    10 kΩ or higher
    B32-97 (VCVL) - Body ground
    Always
    10 kΩ or higher
    B32-68 (VCM) - Body ground
    Always
    10 kΩ or higher
    B32-69 (VCS) - Body ground
    Always
    10 kΩ or higher
    B32-94 (VCEG) - Body ground
    Always
    10 kΩ or higher
    B32-93 (VCPM) - Body ground
    Always
    10 kΩ or higher
    B32-75 (VCIB) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the diesel throttle body assembly connector.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the EGR valve assembly connector.

  1. Reconnect the differential pressure sensor connector.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the battery current sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)