DTC C1380 Stop Light Control Relay Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1380 | Either of the following is detected:
|
|
| 1.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List mode on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
Check that the stop light switch condition observed on the intelligent tester changes according to brake pedal operation.
|
| ||||
| OK | |
| 3.INSPECT SKID CONTROL ECU (STP TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A67-2 (STP) - Body ground | Stop light switch off (Brake pedal released) | Below 1.5 V |
| Stop light switch on (Brake pedal depressed) | 8 to 14 V |
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY) |
Reconnect the skid control ECU connector.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Active Test mode on the intelligent tester (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Stop Light Relay | Stop light control relay (BRK) | Relay ON / OFF | Observe the stop lights. |
Check that the "ON" and "OFF" of the stop lights can be shown on the rear combination light by the intelligent tester.
|
| ||||
| OK | |
| 5.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Perform a road test.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC (C1380) is not output. | A |
| DTC (C1380) is output. | B |
|
| ||||
| A | ||
| ||
| 6.INSPECT STOP LIGHT CONTROL RELAY (BRK) |
![]() |
Turn the ignition switch off.
Remove the stop light control relay (BRK).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 4 | Voltage is not applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 4 | Voltage is applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage is applied between terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 7.INSPECT ENGINE ROOM NO. 1 RELAY BLOCK (POWER SOURCE TERMINAL) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Stop light control relay (BRK) terminal 5 - Body ground | Always | 11 to 14 V |
| Stop light control relay (BRK) terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | |
| 8.INSPECT SKID CONTROL ECU (STPO TERMINAL) |
![]() |
Install the stop light control relay (BRK).
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the skid control ECU connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A67-31 (STPO) - Body ground | Ignition switch ON | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 9.INSPECT SKID CONTROL ECU (STP2 TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A67-22 (STP2) - Body ground | Stop light switch on (Brake pedal depressed) | 8 to 14 V |
| Stop light switch off (Brake pedal released) | Below 1.5 V |
|
| ||||
| OK | ||
| ||