DTC P0877 Transmission Fluid Pressure Sensor / Switch "D" Circuit Low |
DTC P0878 Transmission Fluid Pressure Sensor / Switch "D" Circuit High |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0877 | No. 2 ATF pressure switch off state is detected twice when any of the gears from 4th to 6th engages normally (2-trip detection logic). |
|
| P0878 | No. 2 ATF pressure switch on state is detected twice when any of the gears from 1st to 3rd engages normally (2-trip detection logic). |
| DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| TPS 2 Switch | No. 2 ATF pressure switch status/ ON or OFF |
| - |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0877 OR P0878) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / DTC.
Read the DTCs using the intelligent tester.
| Result | Proceed to |
| Only P0877 is output | A |
| Only P0878 is output | B |
| P0877 or P0878 and other DTCs are output | C |
|
| ||||
|
| ||||
| A | |
| 2.INSPECT TRANSMISSION WIRE (NO. 2 ATF PRESSURE SWITCH) |
![]() |
Disconnect the ATF temperature sensor assembly connector.
Remove the TCM.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| TPS2 ATF temperature sensor assembly side - 20 (TPS2) TCM side | Always | Below 1 Ω |
| TPS2 ATF temperature sensor assembly side - Body ground (valve body assembly) or any other terminals except 20 (TPS2) TCM side | Always | 10 kΩ or higher |
| *1 | Transmission Wire |
| *2 | ATF Temperature Sensor Assembly Side |
| *3 | TCM Side |
|
| ||||
| OK | |
| 3.REPLACE NO. 2 ATF PRESSURE SWITCH (ATF TEMPERATURE SENSOR ASSEMBLY) |
Replace the ATF temperature sensor assembly (Click here).
| NEXT | |
| 4.CHECK IF DTC OUTPUT RECURS (DTC P0877) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / DTC / Clear.
Perform the monitor drive pattern (Click here).
Enter the following menus: Powertrain / ECT / DTC.
Read the DTCs using the intelligent tester.
| Result | Proceed to |
| Only P0877 is output | A |
| DTCs are not output | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT TRANSMISSION WIRE (NO. 2 ATF PRESSURE SWITCH) |
![]() |
Remove the TCM.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 20 (TPS2) - Body ground | Always | 10 kΩ or higher |
| *1 | Component without TCM connected (Transmission Wire) |
|
| ||||
| OK | ||
| ||
| 6.INSPECT NO. 2 ATF PRESSURE SWITCH |
![]() |
Disconnect the ATF temperature sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| TPS2 - Body ground (valve body assembly) or other terminals | Always | 10 kΩ or higher |
| *1 | Component without harness connected (ATF Temperature Sensor Assembly) |
|
| ||||
| OK | ||
| ||