DTC C1439 Steering Angle Sensor Initialization Incomplete |
DTC C1445 Vehicle Driven with Steering Angle Sensor not Initialized |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1439 | After the steering angle sensor 0 calibration is cleared due to, for example, fluctuations in the power source, the steering angle 0 calibration cannot be obtained for 60 seconds of continuous driving. |
|
| C1445 | Steering angle sensor 0 calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor 0 calibration at a speed of 36 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed. |
|

| 1.CHECK DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).
Drive the vehicle at a speed of 36 km/h (22 mph) and turn the steering wheel to the right and left and check that no speed sensor and yaw rate and deceleration sensor DTCs are output (Click here).
| Result | Proceed to | |
| DTC is output. | C1439 or/and C1445 | A |
| Relating to CAN communication system | B | |
| Relating to speed sensor or yaw rate and deceleration sensor | C | |
| DTC is not output. | D | |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION |
Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.
Check that the centered position of the steering wheel is correctly set while driving straight ahead.
| NEXT | |
| 3.RECONFIRM DTC |
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is output. | A |
| DTC is not output. | B |
|
| ||||
| A | |
| 4.READ VALUE USING INTELLIGENT TESTER (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Yaw Rate Open | Yaw rate sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| Deceleration Open | Deceleration sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
| Steering Open | Steering angle sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal | - |
|
| ||||
| OK | |
| 5.REPLACE STEERING ANGLE SENSOR |
Replace the steering angle sensor (Click here).
| NEXT | |
| 6.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION |
Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.
Check that the centered position of the steering wheel is correctly set while driving straight ahead.
| NEXT | |
| 7.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 36 km/h (22 mph) or more and turn the steering wheel to the right and left.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is output. | A |
| DTC is not output. | B |
|
| ||||
| A | ||
| ||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - YAW RATE SENSOR/STEERING ANGLE SENSOR) |
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and yaw rate and deceleration sensor/steering angle sensor (Click here).
| NEXT | |
| 9.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 36 km/h (22 mph) or more and turn the steering wheel to the right and left.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is output. | A |
| DTC is not output. | B |
|
| ||||
| A | |
| 10.REPLACE STEERING ANGLE SENSOR |
Replace the steering angle sensor (Click here).
| NEXT | |
| 11.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION |
Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds.
Check that the centered position of the steering wheel is correctly set while driving straight ahead.
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is output. | A |
| DTC is not output. | B |
|
| ||||
| A | ||
| ||