Home › BRAKE › BRAKE CONTROL › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > TRC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

for 4WD with multi information display:
The TRC OFF indicator is displayed on the multi information display in the combination meter.
for 4WD without multi information display:
The TRC OFF indicator light is located in the combination meter.
The skid control ECU is connected to the combination meter via the CAN communication system.
Pressing the VSC OFF switch turns off traction control and pressing and holding this switch turns off traction and VSC controls. If TRC control turns off, the TRC OFF indicator (light) comes on.

WIRING DIAGRAM


C200786E01


C194134E06


INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
REPAIR CAN COMMUNICATION SYSTEM (Click here)
A


2.INSPECT SKID CONTROL ECU CONNECTOR
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU SECURELY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V

    Result:
    Result
    Proceed to
    OK
    A
    NG
    for 2AD-FHV
    B
    for 2AD-FTV
    C



B
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
A


4.READ VALUE USING INTELLIGENT TESTER (AUTO LSD SWITCH)
  1. Check the Data List for proper functioning of the AUTO LSD switch.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Auto LSD Switch
    Traction control switch (VSC OFF switch) / ON or OFF
    ON: Traction control switch (VSC OFF switch) on
    OFF: Traction control switch (VSC OFF switch) off
    -

    OK:
    ON (VSC OFF switch is ON) appears on the screen.



NG
Go to step 6
OK


5.INSPECT COMBINATION METER ASSEMBLY
  1. Inspect the combination meter (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

6.INSPECT TRACTION CONTROL SWITCH (VSC OFF SWITCH)


    C194196E02
  1. Remove the VSC OFF switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (E) - 9 (+)
    Switch is not pushed
    10 kΩ or higher
    Switch is pushed
    Below 1 Ω



NG
REPLACE TRACTION CONTROL SWITCH (VSC OFF SWITCH)
OK


7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the skid control ECU connector.



    C194149E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-30 (CSW) - E96-9 (+)
    Always
    Below 1 Ω
    A67-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    E96-6 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)