Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P0489    Exhaust Gas Recirculation Control Circuit Low

DTC    P0490    Exhaust Gas Recirculation Control Circuit High

for Preparation Click here


DESCRIPTION

The EGR actuator is operated by the ECM and opens and closes the EGR valve using gears. The opening angle of the EGR valve is detected by the EGR position sensor, which is mounted on the EGR body.

P0489 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 5 seconds or more
The EGR actuator current is below 0.5 A for 2.0 seconds during EGR valve operation.
(1 trip detection logic).
  1. Open or short in EGR valve circuit
  2. EGR valve assembly
  3. ECM

P0490 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idle the engine for 5 seconds or more
An EGR actuator current of 8 A or higher due to a mechanical malfunction, or a Hall IC temperature of 150 to 160°C (302 to 320°F) or higher is detected.
(1 trip detection logic):
  1. Open or short in EGR valve circuit
  2. EGR valve assembly
  3. ECM

Related Data List 
DTC No.
Data List
P0489
  1. Actual EGR Valve Pos.
  2. Target EGR Valve Pos.
P0490

WIRING DIAGRAM

Refer to DTC P0400 .

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.INSPECT EGR VALVE ASSEMBLY
  1. Inspect the electric EGR valve assembly (Click here).



NG
Go to step 4
OK


2.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)


    A204591E07
  1. Disconnect the EGR valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    z1-5 (M+) - B32-86 (EGM+)
    Always
    Below 1 Ω
    z1-1 (M-) - B32-85 (EGM-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    z1-5 (M+) or B32-86 (EGM+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Electric EGR Valve Assembly)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the EGR valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


3.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6

4.REPLACE EGR VALVE ASSEMBLY
  1. Replace the EGR valve assembly (Click here).



NEXT
Go to step 6

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine.

  1. Idle the engine for 5 seconds or more

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END