DTC P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) |
DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0016 | A deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft (bank 1)) signal (2 trip detection logic). |
|
| P0017 | A deviation in the crankshaft position sensor signal and VVT sensor (for exhaust camshaft (bank 1)) signal (2 trip detection logic). |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0016 OR P0017) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0016 or P0017 is output | A |
| DTC P0016 or P0017 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OIL CONTROL VALVE) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Inspect the oil control valve (for intake camshaft).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1).
Check the engine speed when the oil control valve is operated using the intelligent tester when the engine coolant temperature is 50°C (122°F) or less.
| Tester Operation | Specified Condition |
| Oil control valve OFF | Normal engine speed |
| Oil control valve ON | Engine idles roughly or stalls (soon after oil control valve switched from OFF to ON) |
Inspect the oil control valve (for exhaust camshaft).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1).
Check the engine speed when the oil control valve is operated using the intelligent tester when the engine coolant temperature is 50°C (122°F) or less.
| Tester Operation | Specified Condition |
| -128% (Oil control valve OFF) | Normal engine speed |
| 127% (Oil control valve ON) | Engine idles roughly or stalls (soon after oil control valve switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 or P0017 is output | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT) |
![]() |
Remove the camshaft timing oil control valve assembly (for intake camshaft or exhaust camshaft).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
| *1 | Component without harness connected (Camshaft Timing Oil Control Valve) |
![]() |
Apply battery voltage to terminals of the oil control valve assembly (for intake camshaft or exhaust camshaft). Check the valve operation.
Reinstall the oil control valve (for intake camshaft or exhaust camshaft).
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT) |
Inspect the camshaft timing gear assembly (for intake camshaft) .
Inspect the camshaft timing gear assembly (for exhaust camshaft) .
|
| ||||
| OK | |
| 6.ADJUST VALVE TIMING |
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0017) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the ECM from normal mode to check mode using the tester.
Allow the engine to idle for 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0016 and/or P0017 is output | B |
|
| ||||
| A | ||
| ||