DTC P0102 Mass or Volume Air Flow Circuit Low Input |
DTC P0103 Mass or Volume Air Flow Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0102 | The mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic). |
|
| P0103 | The mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic). |
|
| Mass Air Flow Rate (g/sec.) | Malfunction |
| Approximately 0.26 |
|
| 271.0 or more |
|

| 1.CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTC.
| Result | Proceed to |
| DTC P0102 is output | A |
| DTC P0103 is output | B |
|
| ||||
| A | |
| 2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the mass air flow meter connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B1-3 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
Reconnect the mass air flow meter connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-5 (VG) - B32-69 (VG) | Always | Below 1 Ω |
| B1-4 (E2G) - B32-92 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-5 (VG) or B32-69 (VG) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 4.INSPECT MASS AIR FLOW METER |
Inspect the mass air flow meter (Click here).
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY (EFI MAIN)) |
![]() |
Disconnect the mass air flow meter connector.
Remove the integration relay (EFI MAIN relay) from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-3 (+B) - 1A-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-3 (+B) or 1A-4 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Front view of wire harness connector (to Integration Relay) |
| *3 | Engine Room No. 1 Relay Block |
Reconnect the mass air flow meter connector.
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND) |
![]() |
Disconnect the mass air flow meter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (E2G) - Body ground | Always | Below 1 Ω |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
Reconnect the mass air flow meter connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
![]() |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B1-4 (E2G) - B32-92 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B1-4 (E2G) or B32-92 (E2G) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Mass Air Flow Meter) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||