Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0443    Evaporative Emission Control System Purge Control Valve Circuit

for Preparation Click here


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signals to the purge VSV so that the intake amount of evaporated fuel is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No.
DTC Detection Condition
Trouble Area
P0443
The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. ECM

WIRING DIAGRAM


A206572E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE PURGE VSV CONTROL)


    A172375E01
  1. Connect the intelligent tester to the DLC3.

  1. Disconnect the vacuum hose of the charcoal canister from the purge VSV.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. When the purge VSV is operated using the intelligent tester, check whether the purge VSV applies suction to your finger.

    OK:
    Tester Operation
    Specified Condition
    VSV is ON
    Suction of air
    VSV is OFF
    No suction of air

  1. Reconnect the vacuum hose of the charcoal canister to the purge VSV.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT PURGE VSV


    A206531E01
  1. Disconnect the purge VSV connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    23 to 26 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Purge VSV)

  1. Reconnect the purge VSV connector.



NG
REPLACE PURGE VSV (Click here)
OK


3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)


    A107917E56
  1. Disconnect the purge VSV connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B112-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Purge VSV)

  1. Reconnect the purge VSV connector.



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)


    A208651E02
  1. Disconnect the purge VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B112-1 - B32-62 (PRG)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B112-1 or B32-62 (PRG) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Purge VSV)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the purge VSV connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PURGE VSV - ECM)
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY (EFI MAIN RELAY))


    A210498E01
  1. Disconnect the purge VSV connector.

  1. Remove the integration relay (EFI MAIN relay) from the engine room No. 1 relay block and disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B112-2 - 1A-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B112-2 or 1A-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Purge VSV)
    *2
    Front view of wire harness connector
    (to Integration Relay)
    *3
    Engine Room No. 1 Relay Block

  1. Reconnect the purge VSV connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PURGE VSV - INTEGRATION RELAY (EFI MAIN RELAY))
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)