DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 |
|
|
| P0137 |
|
|
| P0138 |
|
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1 S1 (A/F) | +25% | Rich | Below 3.1 V |
| AFS Voltage B1 S1 (A/F) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1 S2 (HO2) | +25% | Rich | Higher than 0.55 V |
| O2S B1 S2 (HO2) | -12.5% | Lean | Below 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC (DTC P0136, P0137 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0138 output | A |
| DTC P0137 output | B |
| DTC P0136 output | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1 S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| Heated Oxygen Sensor Output Voltage | Proceed to |
| 1.0 V or higher | A |
| Below 1.0 V | B |
|
| ||||
| A | |
| 3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+B) - 4 (OX1B) | Always | 10 kΩ or higher |
| 1 (+B) - 3 (E2) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B32-63 (HT1B) - B32-80 (OX1B) | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester, and monitor the output voltage of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1 S1 (A/F) | Alternates between higher than and below 3.3 V | OK |
| AFS Voltage B1 S1 (A/F) | Remains at higher than 3.3 V | NG |
| AFS Voltage B1 S1 (A/F) | Remains at below 3.3 V | NG |

|
| ||||
| OK | |
| 6.INSPECT AIR FUEL RATIO SENSOR |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Drive the vehicle according to the driving pattern listed below:
Warm up the engine until the engine coolant temperature reaches 75°C (167°F) or higher.
Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.
Drive the vehicle at 60 km/h (40 mph) or more and decelerate the vehicle for 5 seconds or more.
Repeat the step above at least 3 times.

Enter the following menus: Powertrain / Engine and ECT / Data List / AFS Current B1 S1.
Read the value of the air fuel ratio sensor current while the fuel-cut operation is performing.
|
| ||||
|
| ||||
| 7.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1 S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Read the output voltage of the heated oxygen sensor when the engine speed is suddenly increased.
|
| ||||
| OK | |
| 8.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Change the fuel injection volume using the tester, and monitor the output voltage of the air fuel ratio sensor and heated oxygen sensor displayed on the tester.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1 S1 (A/F) | Alternates between higher than and below 3.3 V | OK |
| AFS Voltage B1 S1 (A/F) | Remains at higher than 3.3 V | NG |
| AFS Voltage B1 S1 (A/F) | Remains at below 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 9.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (HT1B) - 1 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 2 (HT1B) - 3 (E2) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E2) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E105-2 (HT1B) - B32-63 (HT1B) | Always | Below 1 Ω |
| E105-4 (OX1B) - B32-80 (OX1B) | Always | Below 1 Ω |
| E105-3 (E2) - B32-79 (O1B-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E94-1 (HT1B) - B32-63 (HT1B) | Always | Below 1 Ω |
| E94-3 (OX1B) - B32-80 (OX1B) | Always | Below 1 Ω |
| E94-4 (E2) - B32-79 (O1B-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E105-2 (HT1B) or B32-63 (HT1B) - Body ground | Always | 10 kΩ or higher |
| E105-4 (OX1B) or B32-80 (OX1B) - Body ground | Always | 10 kΩ or higher |
| E105-3 (E2) or B32-79 (O1B-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| E94-1 (HT1B) or B32-63 (HT1B) - Body ground | Always | 10 kΩ or higher |
| E94-3 (OX1B) or B32-80 (OX1B) - Body ground | Always | 10 kΩ or higher |
| E94-4 (E2) or B32-79 (O1B-) - Body ground | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
Reconnect the ECM connector.

|
| ||||
| OK | |
| 12.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137 or P0138.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the driving pattern by accelerating the vehicle to a higher speed and using the second gear to decelerate the vehicle.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136, P0137 or P0138 is output) | B |
|
| ||||
| A | ||
| ||
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OR P0138) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136 or P0138.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the driving pattern by accelerating the vehicle to a higher speed and using the second gear to decelerate the vehicle.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136 or P0138 is output) | B |
|
| ||||
| A | ||
| ||