Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

for Preparation Click here


DESCRIPTION

The Variable Valve Timing (VVT) sensor (G signal) of the intake camshaft consists of a magnet and MRE element.
The VVT camshaft has a timing rotor with 3 teeth on its outer circumference. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE element, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the gear rotation data to pulse signals, and uses the pulse signals to determine the camshaft angle, which it sends to the ECM. Then the ECM uses this data to control fuel injection timing and ignition timing.
The crankshaft position sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft revolution. Based on the G signal and actual crankshaft angle, the ECM detects the normal crankshaft angle. Also, based on the NE signal, the ECM detects the engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0340
  1. The input voltage to the ECM remains at 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more seconds have elapsed after turning the ignition switch to ON (1 trip detection logic).
  2. No camshaft position sensor signal is sent to the ECM during cranking (2 trip detection logic).
  1. Open or short in camshaft position sensor for intake camshaft circuit
  2. Camshaft position sensor for intake camshaft
  3. Intake camshaft
  4. Timing chain jumped tooth
  5. ECM
P0342
The output voltage of the camshaft position sensor is 0.3 V or less for 5 seconds (1 trip detection logic).
  1. Open or short in camshaft position sensor for intake camshaft circuit
  2. Camshaft position sensor for intake camshaft
  3. Intake camshaft
  4. Timing chain jumped tooth
  5. ECM
P0343
The output voltage of the camshaft position sensor is 4.7 V or higher for 5 seconds (1 trip detection logic).
  1. Open or short in camshaft position sensor for intake camshaft circuit
  2. Camshaft position sensor for intake camshaft
  3. Intake camshaft
  4. Timing chain jumped tooth
  5. ECM

WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.
  2. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0340, P0342 OR P0343)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0340, P0342 or P0343 is output
    A
    DTC P0340, P0342 or P0343 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0340, P0342 or P0343 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT (SENSOR POWER SOURCE)


    A208648E03
  1. Disconnect the camshaft position sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B123-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Camshaft Position Sensor)

  1. Reconnect the camshaft position sensor connector.



NG
Go to step 10
OK


3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT - ECM)


    A208649E05
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B123-1 (VV1+) - B32-94 (G2+)
    Always
    Below 1 Ω
    B123-2 (VV1-) - B32-118 (G2-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B123-1 (VV1+) or B32-94 (G2+) - Body ground
    Always
    10 kΩ or higher
    B123-2 (VV1-) or B32-118 (G2-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Camshaft Position Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the camshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT - ECM)
OK


4.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT)


    A208464E02
  1. Check the camshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT (Click here)
OK


5.CHECK INTAKE CAMSHAFT
  1. Check the teeth of the intake camshaft.

    OK:
    Camshaft teeth do not have any cracks or deformation.



NG
REPLACE INTAKE CAMSHAFT (Click here)
OK


6.REPLACE CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT
  1. Replace the camshaft position sensor for intake camshaft (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0340, P0342 or P0343 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A


8.ADJUST VALVE TIMING

HINT:
There are no marks on the cylinder head to align for the purpose of checking valve timing. Valve timing can only be inspected by aligning the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and reinstall the chain to align the timing marks .


NEXT


9.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0340, P0342 or P0343 are output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

10.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT - ECM)


    A208649E06
  1. Disconnect the camshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B123-3 (VC) - B32-119 (VCV1)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B123-3 (VC) or B32-119 (VCV1) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Camshaft Position Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the camshaft position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT - ECM)
OK

REPLACE ECM (Click here)