Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)

DTC    P101D    A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON

for Preparation Click here


DESCRIPTION

Refer to DTC P2195 (Click here).

HINT:
  1. Although the DTC titles refer to the oxygen sensor, these DTCs relate to the air fuel ratio sensor.
  2. Sensor 1 refers to the sensor mounted in front of the three way catalytic converter and located near the engine assembly.
  3. When either of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

  4. The ECM provides a pulse width modulated signal to the control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.


    A210603E01


DTC No.
DTC Detection Condition
Trouble Area
P0031
The air fuel ratio sensor heater current is below 0.8 A (1 trip detection logic).
  1. Open in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (sensor 1)
  3. Integration relay (EFI MAIN relay)
  4. ECM
P0032
The air fuel ratio sensor heater current is higher than 10 A (1 trip detection logic).
  1. Short in air fuel ratio sensor heater circuit
  2. Air fuel ratio sensor heater (sensor 1)
  3. Integration relay (EFI MAIN relay)
  4. ECM
P101D
The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
ECM

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)


    A157520E31
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    20°C (68°F)
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE)


    A079114E23
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B113-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)


    A208636E05
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B113-1 (HA1A) - B32-104 (HA1A)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B113-1 (HA1A) or B32-104 (HA1A) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)
    *2
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0031 OR P101D)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0031, P0032 or P101D is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY (EFI MAIN))


    A210492E01
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the integration relay (EFI MAIN relay) from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B113-2 (+B) - 1A-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B113-2 (+B) or 1A-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)
    *2
    Front view of wire harness connector
    (to Integration Relay)
    *3
    Engine Room No. 1 Relay Block

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY (EFI MAIN))
OK

GO TO ECM POWER SOURCE CIRCUIT (Click here)