SFI SYSTEM > Fuel Injector Circuit |

| 1.CHECK FUEL INJECTOR (POWER SOURCE) |
![]() |
Disconnect the fuel injector connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| B16-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B14-1 - Body ground | Ignition switch ON | 11 to 14 V |
| B13-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector) |
Turn the ignition switch off.
Reconnect the fuel injector connectors.
|
| ||||
| OK | |
| 2.INSPECT FUEL INJECTOR |
Inspect the fuel injector (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM) |
![]() |
Disconnect the fuel injector connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-2 - B32-86 (#10) | Always | Below 1 Ω |
| B15-2 - B32-85 (#20) | Always | Below 1 Ω |
| B14-2 - B32-84 (#30) | Always | Below 1 Ω |
| B13-2 - B32-83 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B16-2 or B32-86 (#10) - Body ground | Always | 10 kΩ or higher |
| B15-2 or B32-85 (#20) - Body ground | Always | 10 kΩ or higher |
| B14-2 or B32-84 (#30) - Body ground | Always | 10 kΩ or higher |
| B13-2 or B32-83 (#40) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Fuel Injector) |
| *1 | Front view of wire harness connector (to ECM) |
Reconnect the fuel injector connectors.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 4.INSPECT INTEGRATION NO.1 RELAY (IGT/INJ RELAY) |
![]() |
Remove the integration relay from the engine room No. 1 relay block.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - 1B-8 | Battery voltage not applied to terminals 1B-6 and 1B-7 | 10 kΩ or higher |
| 1C-1 - 1B-8 | Battery voltage applied to terminals 1B-6 and 1B-7 | Below 1 Ω |
| *1 | Component without harness connected (Integration Relay) |
Reconnect the integration relay connector.
Reinstall the integration relay.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (IGT/INJ) - FUEL INJECTOR) |
![]() |
Disconnect the fuel injector connectors.
Remove the integration relay from the engine room No. 1 relay block.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B16-1 - 1B-8 | Always | Below 1 Ω |
| B15-1 - 1B-8 | Always | Below 1 Ω |
| B14-1 - 1B-8 | Always | Below 1 Ω |
| B13-1 - 1B-8 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B16-1 or 1B-8 - Body ground | Always | 10 kΩ or higher |
| B15-1 or 1B-8 - Body ground | Always | 10 kΩ or higher |
| B14-1 or 1B-8 - Body ground | Always | 10 kΩ or higher |
| B13-1 or 1B-8 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Fuel Injector) |
| *2 | Front view of wire harness connector (to Integration Relay) |
| *3 | Engine Room No. 1 Relay Block |
Reconnect the integration relay connector.
Reinstall the integration relay.
Reconnect the fuel injector connectors.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY (EFI MAIN RELAY) - (IGT/INJ)) |
![]() |
Remove the integration relay from the engine room No. 1 relay block.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1A-4 - 1B-6 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 1A-4 or 1B-6 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Integration Relay) |
| *2 | Engine Room No. 1 Relay Block |
Reconnect the integration relay connector.
Reinstall the integration relay.
|
| ||||
| OK | ||
| ||