Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM

ANTI-LOCK BRAKE SYSTEM > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

If any of the following conditions are detected, the brake warning light remains on:
  1. The ECU connectors are disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. The EBD is defective.

WIRING DIAGRAM


C203615E01


INSPECTION PROCEDURE

1.PREPARE FOR INSPECTION
  1. Check that both of the following conditions are satisfied.

    1. The brake fluid level in the brake master cylinder reservoir is correct.
    2. The parking brake is released.

    HINT:
    When the ABS warning light remains illuminated, repair the malfunctions in the ABS system first.


NEXT


2.CHECK DTC FOR ABS
  1. Check if any ABS DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


3.CHECK CAN COMMUNICATION SYSTEM
  1. Check if the CAN communication system DTC is output (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


4.INSPECT SKID CONTROL ECU CONNECTOR
  1. Check if the skid control ECU connector is properly installed.

    OK:
    The skid control ECU connector is properly installed.



NG
CONNECT CONNECTOR TO ECU SECURELY
OK


5.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)


    C117862E11
  1. Disconnect the A27 ECU connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    A27-2 (GND1) - Body ground
    Below 1 Ω
    A27-24 (GND2) - Body ground
    Below 1 Ω

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A27-25 (IG) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)
  1. Using the Data List, check for proper functioning of the parking brake switch.

    Skid control ECU 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Notes
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

    OK:
    When the parking brake lever is operated, the display changes as shown above.



NG
Go to step 10
OK


7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C203620E01
  1. Remove the reservoir tank cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance of the switch.

    HINT:
    A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake fluid level.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+) - 2 (E)
    Float up (Switch OFF)
    10 kΩ or higher
    1 (+) - 2 (E)
    Float down (Switch ON)
    Below 1 Ω

    HINT:
    If there is no problem after the above check is finished, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY
OK


8.CHECK WIRE HARNESS (COMBINATION METER - LEVEL WARNING SWITCH AND BODY GROUND)


    C126282E10
  1. Disconnect the E22 combination meter connector.

  1. Disconnect the A10 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E22-14 (SW) - A10-1 (+)
    Below 1 Ω
    E22-14 (SW) - Body ground
    10 kΩ or higher
    A10-2 (E) - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


9.CHECK COMBINATION METER
  1. Check the combination meter (Click here).



NG
REPLACE COMBINATION METER (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

10.INSPECT PARKING BRAKE SWITCH ASSEMBLY


    C118703E03
  1. Remove the parking brake switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin not pushed)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH ASSEMBLY (Click here)
OK


11.CHECK WIRE HARNESS (JUNCTION BLOCK - PARKING BRAKE SWITCH AND BODY GROUND)


    C126283E01
  1. Disconnect the ID junction block connector.

  1. Disconnect the E46 switch connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    ID-4 (PKB) - E46-1
    Below 1 Ω
    ID-4 (PKB) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)