SFI SYSTEM > Cranking Holding Function Circuit |


| 1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the ignition switch is turned to ON, and when the engine is cranking.
| Condition | Tester Display (Starter Signal) |
| Ignition switch ON | OFF |
| Engine cranking | ON |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK ECM (STSW TERMINAL VOLTAGE) |
![]() |
Disconnect the ECM connector.
Depress the clutch pedal fully (for Manual Transaxle).
Move the shift lever to N (for CVT).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A12-29 (STSW) - Body ground | Engine starts | 11 to 14 V |
| Result | Proceed to |
| OK (for Manual Transaxle) | A |
| OK (for CVT) | B |
| NG | C |
Reconnect the ECM connector.
|
| ||||
|
| ||||
| A | |
| 3.CHECK CLUTCH START SWITCH ASSEMBLY (INPUT VOLTAGE) |
![]() |
Disconnect the clutch start switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A4-2 - Body ground | Engine cranking | 11 to 14 V |
| *1 | Front view of wire harness connector (to Clutch Start Switch Assembly) |
Reconnect the clutch start switch assembly connector.
|
| ||||
| OK | |
| 4.INSPECT CLUTCH START SWITCH ASSEMBLY |
![]() |
Remove the clutch start switch assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 2 | Pushed | Below 1 Ω |
| 1 - 2 | Not pushed | 10 kΩ or higher |
Reinstall the clutch start switch assembly.
|
| ||||
| OK | ||
| ||
| 5.CHECK PARK/NEUTRAL POSITION SWITCH (INPUT VOLTAGE) |
![]() |
Disconnect the park/neutral position switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B28-4 - Body ground | Engine cranking | 11 to 14 V |
| *1 | Front view of wire harness connector (to Park/Neutral Position Switch) |
Reconnect the park/neutral position switch connector.
|
| ||||
| OK | |
| 6.INSPECT PARK/NEUTRAL POSITION SWITCH |
Inspect the park/neutral position switch (Click here).
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (ECM - MAIN BODY ECU) |
![]() |
Disconnect the main body ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E20-4 (STSW) - A12-29 (STSW) | Always | Below 1 Ω |
| E20-4 (STSW) or A12-29 (STSW) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Main Body ECU) |
| *2 | Front view of wire harness connector (to ECM) |
Reconnect the main body ECU connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 8.INSPECT ST CUT RELAY |
![]() |
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage not applied to terminal 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminal 1 and 2 | Below 1 Ω |
Reinstall the relay.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - BODY GROUND) |
![]() |
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST CUT relay terminal 1 - Body ground | Always | Below 1 Ω |
| *1 | No. 7 Relay Block |
| *2 | ST CUT |
Reinstall the ST CUT relay.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - IGNITION RELAY NO. 2 (IG2)) |
![]() |
Remove the ST CUT relay from the No. 7 relay block.
Remove the ignition relay No. 2 (IG2) from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Ignition relay No. 2 (IG2) terminal 5 - ST CUT relay terminal 2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| Ignition relay No. 2 (IG2) terminal 5 or ST CUT relay terminal 2 - Body ground | Always | 10 kΩ or higher |
| *1 | Engine Room No. 1 Relay Block |
| *2 | IG2 |
| *3 | No. 7 Relay Block |
| *4 | ST CUT |
Reinstall the ST CUT relay.
Reinstall the ignition relay No. 2 (IG2).
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - ECM) |
![]() |
Disconnect the ECM connector.
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST CUT relay terminal 3 - B32-51 (STAR) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| ST CUT relay terminal 3 or B32-51 (STAR) - Body ground | Always | 10 kΩ or higher |
| *1 | No. 7 Relay Block |
| *2 | ST CUT |
| *3 | Front view of wire harness connector (to ECM) |
Reconnect the ECM connector.
Reinstall the ST CUT relay.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - MAIN BODY ECU) |
![]() |
Disconnect the main body ECU connector.
Remove the ST CUT relay from the No. 7 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST CUT relay terminal 3 - E20-14 (STR2) | Always | Below 1 Ω |
| ST CUT relay terminal 5 - E20-3 (STR) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| ST CUT relay terminal 3 or E20-14 (STR2) - Body ground | Always | 10 kΩ or higher |
| ST CUT relay terminal 5 or E20-3 (STR) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Main Body ECU) |
| *2 | No. 7 Relay Block |
| *3 | ST CUT |
Reconnect the main body ECU connector.
Reinstall the ST CUT relay.
| Result | Proceed to |
| OK (for Manual Transaxle) | A |
| OK (for CVT) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CLUTCH START SWITCH ASSEMBLY) |
![]() |
Disconnect the main body ECU connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E20-3 (STR) - A4-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E20-3 (STR) or A4-2 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Main Body ECU) |
| *2 | Front view of wire harness connector (to Clutch Start Switch Assembly) |
Reconnect the main body ECU connector.
Reconnect the clutch start switch assembly connector.
|
| ||||
| OK | ||
| ||
| 14.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the main body ECU connector.
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E20-3 (STR) - B28-4 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| E20-3 (STR) or B28-4 - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Main Body ECU) |
| *2 | Front view of wire harness connector (to Park/Neutral Position Switch) |
Reconnect the main body ECU connector.
Reconnect the park/neutral position switch connector.
|
| ||||
| OK | ||
| ||
| 15.CHECK ST RELAY (INPUT VOLTAGE) |
![]() |
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 1 - Body ground | Engine cranking | 11 to 14 V |
Reinstall the ST relay.
|
| ||||
| OK | |
| 16.INSPECT ST RELAY |
Remove the ST relay from the No. 7 relay block (for LHD).
![]() |
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage not applied to terminal 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied to terminal 1 and 2 | Below 1 Ω |
Reinstall the ST relay.
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND) |
![]() |
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 2 - Body ground | Always | Below 1 Ω |
Reinstall the ST relay.
|
| ||||
| OK | |
| 18.CHECK ST RELAY (INPUT VOLTAGE) |
![]() |
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| ST relay terminal 5 - Body ground | Ignition switch ON | 11 to 14 V |
Reinstall the ST relay.
|
| ||||
| OK | |
| 19.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER) |
![]() |
Remove the ST relay from the No. 7 relay block (for LHD).
Remove the ST relay from the No. 8 relay block (for RHD).
Disconnect the starter connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 3 - B26-1 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| ST relay terminal 3 or B26-1 - Body ground | Always | 10 kΩ or higher |
Reinstall the ST relay.
Reconnect the starter connector.
|
| ||||
| OK | |
| 20.INSPECT STARTER |
Inspect the starter (Click here).
|
| ||||
| OK | ||
| ||