Home › TRANSMISSION ยท E352 MANUAL TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY

MANUAL TRANSAXLE ASSEMBLY > REMOVAL

for Preparation Click here



1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


2. REMOVE FRONT WHEELS


3. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.

  1. Remove the console box .



    A128750E01
  1. Disconnect the connector.

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.



    A128750E01
  1. Connect the connector.

  1. Install the console box .



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



5. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



6. REMOVE STARTER ASSEMBLY (for 1AZ-FE)
  1. Remove the starter (Click here).



7. REMOVE STARTER ASSEMBLY (for 2AZ-FE)
  1. for 1.6 kW Type:
    Remove the starter (Click here).

  1. for 1.7 kW Type:
    Remove the starter (Click here).



8. REMOVE ENGINE ASSEMBLY WITH MANUAL TRANSAXLE
  1. for 1AZ-FE:
    Remove the engine with manual transaxle (Click here).

  1. for 2AZ-FE:
    Remove the engine with manual transaxle (Click here).



9. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


D026905E01
  1. Disconnect the back-up light switch connector.

  1. Remove the back-up light switch and gasket from the transaxle case.



10. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY
  1. for 1AZ-FE:
    Disconnect the clutch release cylinder (Click here).

  1. for 2AZ-FE:
    Disconnect the clutch release cylinder (Click here).



11. DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY


C127255
  1. Remove the 2 clips and 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips, and disconnect the 2 cables from the bracket.



12. REMOVE FRONT ENGINE MOUNTING BRACKET


C129224
  1. Remove the 3 bolts and bracket.



13. REMOVE ENGINE MOUNTING BRACKET LH


C129226
  1. Remove the 3 bolts and bracket.



14. REMOVE REAR ENGINE MOUNTING BRACKET


C132028
  1. Remove the 3 bolts and mounting bracket.



15. REMOVE OIL PAN INSULATOR


C127239
  1. Remove the 2 bolts and insulator from the stiffener plate.



16. REMOVE STIFFENER PLATE LH


C127240
  1. Remove the 4 bolts and stiffener plate.



17. REMOVE STIFFENER PLATE RH


C127241
  1. Remove the 4 bolts and stiffener plate.



18. REMOVE MANUAL TRANSAXLE ASSEMBLY


D025747E01
  1. Remove the 10 bolts.

  1. Remove the transaxle from the engine.



19. REMOVE MANUAL TRANSAXLE CASE PROTECTOR


D030076E01
  1. Remove the 2 bolts and case protector.