NAVIGATION SYSTEM (for DVD) > Reverse Signal Circuit |


| 1.CHECK NAVIGATION RECEIVER ASSEMBLY (DISPLAY CHECK MODE) |
![]() |
Enter the "Display Check" mode and select "Vehicle Signal Check Mode" (Click here).
Check that the display changes between ON and OFF according to the shift lever operation.
| Shift Lever Position | Display |
| R | ON |
| Except R | OFF |
|
| ||||
| OK | ||
| ||
| 2.CHECK NAVIGATION RECEIVER ASSEMBLY (REVERSE SIGNAL) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E57-5 (REV) - Body ground | Ignition switch ON Shift lever in R | 11 to 14 V |
| E57-5 (REV) - Body ground | Ignition switch ON Shift lever in any position except R | Below 1 V |
|
| ||||
| OK | ||
| ||
| 3.CHECK TRANSAXLE TYPE |
Check the transaxle type.
| Result | Proceed to |
| CVT | A |
| Automatic Transaxle | B |
| Manual Transaxle | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the E57 navigation receiver assembly connector.
![]() |
Disconnect the B28 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E57-5 (REV) - B28-2 (RL) | Always | Below 1 Ω |
| E57-5 (REV) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Disconnect the B28 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (RB) - 2 (RL) | Shift lever in R | Below 1 Ω |
| 1 (RB) - 2 (RL) | Shift lever in P | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the E57 navigation receiver assembly connector.
![]() |
Disconnect the B28 park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E57-5 (REV) - B28-2 (RL) | Always | Below 1 Ω |
| E57-5 (REV) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Disconnect the B28 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (RL) - 2 (RB) | Shift lever in R | Below 1 Ω |
| 1 (RL) - 2 (RB) | Shift lever in P | 10 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (U140F) | B |
| NG (U241E) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BACK-UP LIGHT SWITCH) |
![]() |
Disconnect the E57 navigation receiver assembly connector.
![]() |
Disconnect the B25 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E57-5 (REV) - B25-1 | Always | Below 1 Ω |
| E57-5 (REV) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY |
![]() |
Disconnect the B25 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Shift lever in R | Below 1 Ω |
| 1 - 2 | Shift lever not in R | 10 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (EB61) | B |
| NG (EB61F) | C |
| NG (E352F) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||