Home › ENGINE · 3ZR-FAE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Fuel Pump Control Circuit

for Preparation Click here


DESCRIPTION

When the engine is cranked, current flows from terminal ST1 (STR) of the ignition switch (main body ECU) to the starter relay coil and current also flows to terminal STA of the ECM (STA signal).
When the STA signal and NE signal are input to the ECM, Tr is turned on, current flows to the coil of the circuit opening relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.
While the NE signal is generated (engine running), the ECM keeps Tr on (circuit opening relay on) and the fuel pump also keeps operating.

A210086E01


WIRING DIAGRAM


A210087E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE C/OPN RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether the fuel pump operation sound occurs when performing the Active Test on the tester.

    OK:
    Fuel pump operating sound occurs.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK (C/OPN RELAY)


    A116124E41
  1. Disconnect the instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IB-11 - IA-8
    Battery voltage not applied to terminals IE-5 and IF-4
    10 kΩ or higher
    Battery voltage applied to terminals IE-5 and IF-4
    Below 1 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Instrument Panel Junction Block)

  1. Reconnect the instrument panel junction block connector.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK (C/OPN RELAY)
OK


3.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - ECM)


    A133158E09
  1. Disconnect the ECM connector.

  1. Disconnect the instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    IE-5 - A12-19 (FC)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    IE-5 or A12-19 (FC) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Instrument Panel Junction Block)
    *2
    Instrument Panel Junction Block
    *3
    Front view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.

  1. Reconnect the instrument panel junction block connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - ECM)
OK


4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - INTEGRATION RELAY [EFI MAIN RELAY], IG2 RELAY)


    A210597E01
  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Disconnect the integration relay connector.

  1. Remove the ignition relay No. 2 (IG2).

  1. Disconnect the instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    1A-4 - IB-11
    Always
    Below 1 Ω
    Ignition relay No. 2 (IG2) terminal 5 - IF-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    1A-4 or IB-11 - Body ground
    Always
    10 kΩ or higher
    Ignition relay No. 2 (IG2) terminal 5 or IF-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Integration Relay)
    *2
    Engine Room No. 1 Relay Block
    *3
    IG2
    *4
    Front view of wire harness connector
    (to Instrument Panel Junction Block)

  1. Reconnect the instrument panel junction block connector.

  1. Reinstall the ignition relay No. 2 (IG2).

  1. Reconnect the integration relay connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - INTEGRATION RELAY [EFI MAIN RELAY], IG2 RELAY)
OK


5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)


    A133159E05
  1. Disconnect the fuel pump connector.

  1. Disconnect the instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    IA-8 - T1-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    IA-8 or T1-4 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Instrument Panel Junction Block)
    *2
    Instrument Panel Junction Block
    *3
    Front view of wire harness connector
    (to Fuel Pump)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN RELAY - FUEL PUMP)
OK


6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)


    A148746E15
  1. Disconnect the fuel pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T1-5 - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Fuel Pump)

  1. Reconnect the fuel pump connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)
OK


7.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).



NG
REPLACE FUEL PUMP (Click here)
OK


8.CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).



NG
REPAIR ECM POWER SOURCE CIRCUIT
OK

REPLACE ECM (Click here)