Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/ Entry and Start System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the ID code box is stuck on HI output, the ECM outputs this DTC.

DTC Code
DTC Detection Condition
Trouble Area
B279A
The communication line (EFIO-IMI) between the ECM and the ID code box is stuck on HI output.
  1. Wire harness
  2. ID code box
  3. ECM

WIRING DIAGRAM


B160072E15


INSPECTION PROCEDURE

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    If DTCs other than DTC B279A are output, troubleshoot those DTCs first.

    Result 
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B



B
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
E180658E06
  1. Disconnect the E51 box connector.

  1. Disconnect the A12 ECM connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E51-6 (EFIO) - A12-11 (IMI)
    Always
    Below 1 Ω
    E51-6 (EFIO) or A12-11 (IMI) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E51-6 (EFIO) - Body ground
    Always
    Below 1 V
    A12-11 (IMI) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK ID CODE BOX (OUTPUT)

B178967E04

  1. Using an oscilloscope, check the waveform.
    Measurement Condition 
    Item
    Content
    Tester Connection
    E51-6 (EFIO) - E51-8 (GND)
    Tool Setting
    10 V/DIV., 100 msec./DIV.
    Condition
    Engine switch on (IG)

    OK:
    Waveform is output normally (see illustration).

    Result 
    Result
    Proceed to
    OK (for 1AZ-FE)
    A
    OK (for 2AZ-FE)
    B
    OK (for 3ZR-FAE)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
Go to step 5
A

REPLACE ECM (Click here)  

5.CHECK ID CODE BOX (POWER SOURCE AND BODY GROUND)
B164101E10
  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connector
    Condition
    Specified Condition
    E51-1 (+B) - E51-8 (GND)
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE ID CODE BOX
  1. Replace the ID code box.


NEXT


7.ECU CODE REGISTRATION
  1. Register the ECU code.


NEXT


8.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.


NEXT


9.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


10.CHECK DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B279A is not output
    A
    DTC B279A is output (for 1AZ-FE)
    B
    DTC B279A is output (for 2AZ-FE)
    C
    DTC B279A is output (for 3ZR-FAE)
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A

END (ID CODE BOX IS DEFECTIVE)