When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P0300 | Random / Multiple Cylinder Misfire Detected | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
Intake air control valve actuator (for tumble control valve) ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | DTC for Mexico Models
- Applies |
| P0301 | Cylinder 1 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
Intake air control valve actuator (for tumble control valve) ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | DTC for Mexico Models
- Applies |
| P0302 | Cylinder 2 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
Intake air control valve actuator (for tumble control valve) ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | DTC for Mexico Models
- Applies |
| P0303 | Cylinder 3 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
Intake air control valve actuator (for tumble control valve) ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | DTC for Mexico Models
- Applies |
| P0304 | Cylinder 4 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
Intake air control valve actuator (for tumble control valve) ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | DTC for Mexico Models
- Applies |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs once.
An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
At a high engine speed, a sufficient number of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
At a normal engine speed, a sufficient number of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.
An excessive number of misfires (approximately 500 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause the three-way catalytic converter damage, is detected.
A catalyst-damaging misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.
| Related DTCs | P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire P0302: Cylinder 2 misfire P0303: Cylinder 3 misfire P0304: Cylinder 4 misfire |
| Required Sensors/Components (Main) | Crankshaft position sensor
Camshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature
Intake air temperature sensor Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Duration | 1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emission-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire) |
| MIL Operation | 2 driving cycles: Emission-related misfire
MIL flashes immediately: Catalyst-damaging misfire |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0016 (VVT system - misalignment)
P0017 (Exhaust VVT system - misalignment) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328 (Knock control sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0351 - P0354 (Igniter) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) |
| Battery voltage | 8 V or higher |
| VVT system | Not operated by scan tool |
| Engine speed | 400 to 6300 rpm |
| Either of the following conditions is met | A or B |
| A. Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| B. Engine coolant temperature | Higher than 20°C (68°F) |
| Fuel cut | Off |
| First 1000 revolutions after engine start, or during check mode | Crankshaft 1000 revolutions |
| Except above | Crankshaft 1000 revolutions x 4 |
| All of the following conditions 1, 2, 3 and 4 met | Crankshaft 200 revolutions x 3 |
| Except above (MIL blinks immediately) | Crankshaft 200 revolutions |
| 1. Driving cycles | 1st |
| 2. Check mode | Off |
| 3. Engine speed | Less than 2450 rpm |
| 4. Intake air amount per revolution | Less than 0.95 g/rev |
| Monitor runs whenever the following DTCs are not stored | P0016 (VVT system - misalignment)
P0017 (Exhaust VVT system - misalignment) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328 (Knock control sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Crankshaft position sensor) P0351 - P0354 (Igniter) P0500 (Vehicle speed sensor) P0705 (Shift lever position switch) |
| Battery voltage | 8 V or higher |
| VVT system | Not operated by scan tool |
| Engine speed | 400 to 6300 rpm |
| Engine coolant temperature | Higher than 65°C (149°F) |
| Fuel cut | Off |
| First 1000 revolutions after engine start, or check mode | Crankshaft 1000 revolutions |
| Except above | Crankshaft 1000 revolutions x 4 |
| Both of the following conditions 1 and 2 met: | Crankshaft 200 revolutions x 3 |
| 1. Driving cycles | 1st |
| 2. Check mode | Off |
| Except above (MIL blinks immediately) | Crankshaft 200 revolutions |
| Misfire rate | 1.493% or higher |
| Number of misfires per 200 revolutions | 130 or more (varies with intake air amount and engine speed) |
| Misfire rate | 50% or higher: for 1st 1000 revolutions
25% or higher: after 1st 1000 revolutions |
| Number of misfires per 200 revolutions | 130 or more (varies with intake air amount and engine speed) |
Refer to detailed information in Checking Monitor Status.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>CHECKING MONITOR STATUS
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A1 | $0B | Multiply by 1 | Time | Total EWMA* misfire count of all cylinders in last ten driving cycles |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A1 | $0C | Multiply by 1 | Time | ·
When ignition switch is ON, total misfire count of all cylinders in last driving cycle is displayed. ·
While engine is running, total misfire count of all cylinders in current driving cycle is displayed. |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A2 | $0B | Multiply by 1 | Time | Total EWMA* misfire count of cylinder 1 in last ten driving cycles |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A2 | $0C | Multiply by 1 | Time | ·
When ignition switch is ON, total misfire count of cylinder 1 in last driving cycle is displayed. ·
While engine is running, total misfire count of cylinder 1 in current driving cycle is displayed. |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A3 | $0B | Multiply by 1 | Time | Total EWMA* misfire count of cylinder 2 in last ten driving cycles |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A3 | $0C | Multiply by 1 | Time | ·
When ignition switch is ON, total misfire count of cylinder 2 in last driving cycle is displayed. ·
While engine is running, total misfire count of cylinder 2 in current driving cycle is displayed. |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A4 | $0B | Multiply by 1 | Time | Total EWMA* misfire count of cylinder 3 in last ten driving cycles |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A4 | $0C | Multiply by 1 | Time | ·
When ignition switch is ON, total misfire count of cylinder 3 in last driving cycle is displayed. ·
While engine is running, total misfire count of cylinder 3 in current driving cycle is displayed. |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A5 | $0B | Multiply by 1 | Time | Total EWMA* misfire count of cylinder 4 in last ten driving cycles |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $A5 | $0C | Multiply by 1 | Time | ·
When ignition switch is ON, total misfire count of cylinder 4 in last driving cycle is displayed. ·
While engine is running, total misfire count of cylinder 4 in current driving cycle is displayed. |
*: EWMA (Exponential Weighted Moving Average) misfire counts for last 10 driving cycles (calculated) Calculation: 0.1 x (current counts) + 0.9 x (previous average) Initial value for (previous average) = 0
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Using the Techstream, switch the ECM from normal mode to check mode.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the ignition switch off and wait for at least 30 seconds.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Refer to DTC P0102.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0102
Refer to Fuel Injector Circuit.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit
Inspect the fuses for circuits related to this system before performing the following procedure.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or higher).
When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections
Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
PCV valve and hose are correctly connected and are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Misfire RPM and Misfire Load.
| Tester Display |
|---|
| Misfire RPM |
| Misfire Load |
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Catalyst OT MF F/C.
| Tester Display |
|---|
| Catalyst OT MF F/C |
Read the value displayed on the Techstream.
| Data List | Techstream Display | Proceed to |
|---|---|---|
| Catalyst OT MF F/C | Avail | A |
| Not Avl | B |
A
B
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire Prevent F/C.
| Tester Display |
|---|
| Prohibit the Catalyst OT Misfire prevent F/C |
Perform the Active Test.
When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.
| Tester Display |
|---|
| Cylinder #1 Misfire Count |
| Cylinder #2 Misfire Count |
| Cylinder #3 Misfire Count |
| Cylinder #4 Misfire Count |
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the Techstream [B].
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.
A
B
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B77-20 (#10) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| B77-17 (#20) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| B77-18 (#30) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| B77-19 (#40) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake air control valve actuator (for tumble control valve).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL
Check the fuel pressure.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake air control valve actuator (for tumble control valve).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL
Check the fuel pressure.
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
OK
NG
OK
NG
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B77-20 (#10) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| B77-17 (#20) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| B77-18 (#30) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| B77-19 (#40) - B77-50 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
A |
| NORMAL
(DTC is not output) |
B |
A
B
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
If the results of the inspections performed in steps 16 and 22 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTC is not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
B |
A
B
Check the fuel lines for leaks or blockage.
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG