The camshaft position sensor for the intake camshaft (VV1 signal) consists of a magnet and MRE (Magneto Resistance Element).
The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection and injection timing.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P0340 | Camshaft Position Sensor Circuit Malfunction | When one of the following conditions is met:
·
No camshaft position sensor signal to the ECM while cranking (2 trip detection logic). ·
A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher (1 trip detection logic). |
·
Open or short in camshaft position sensor circuit (for intake camshaft) ·
Camshaft position sensor (for intake camshaft) ·
Intake camshaft ·
Valve timing ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P0342 | Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) | The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for intake camshaft) ·
Camshaft position sensor (for intake camshaft) ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P0343 | Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) | The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit (for intake camshaft) ·
Camshaft position sensor (for intake camshaft) ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
VV1 stands for the camshaft position sensor signal (for intake camshaft), and EV1 stands for the camshaft position sensor signal (for exhaust camshaft).
| ECM Terminal Name | CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
If no pulse signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.
| Related DTCs | P0340: Camshaft position sensor verify pulse input
P0342: Camshaft position sensor range check (low voltage) P0343: Camshaft position sensor range check (high voltage) |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 4 seconds: Camshaft position sensor verify pulse input (case 1) (P0340), Camshaft position sensor range check (P0342, P0343)
5 seconds: Camshaft position sensor verify pulse input (case 2) (P0340) |
| MIL Operation | 2 driving cycles: Camshaft position sensor verify pulse input (case 1) (P0340)
Immediate: Camshaft position sensor verify pulse input (case 2) (P0340), Camshaft position sensor range check (P0342, P0343) |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| Both of the following conditions are met | - |
| Starter | On and not starter on again |
| Minimum battery voltage while starter on | Below 11 V |
| All of the following conditions are met | - |
| Engine speed | 600 rpm or higher |
| Starter | Off |
| Camshaft position sensor voltage | 0.3 to 4.7 V |
| VVT system misalignment | Not detected |
| Camshaft position sensor range check fail | Not detected |
| All of the following conditions are met | - |
| Starter | Off |
| Ignition switch | ON |
| Time after ignition switch turned from off to ON | 2 seconds or more |
| Battery voltage | 8 V or higher |
| Camshaft position sensor verify pulse input fail | Not detected |
| Camshaft position sensor signal | No signal |
| Either of the following conditions is met | 1 or 2 |
| 1. Camshaft position and crankshaft position phase | Misaligned |
| 2. Camshaft position sensor signal | No signal |
| Camshaft position sensor voltage | Below 0.3 V |
| Camshaft position sensor voltage | Higher than 4.7 V |
| Camshaft position sensor voltage | 0.3 to 4.7 V |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine.
Idle the engine for 10 seconds or more [A].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0340, P0342 or P0343.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Camshaft Position Sensor for Intake Camshaft) |
Disconnect the camshaft position sensor for intake camshaft connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B39-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the camshaft position sensor for intake camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B39-1 (VV1+) - B77-82 (VV1+) | Always | Below 1 Ω |
| B39-2 (VV1-) - B77-114 (VV1-) | Always | Below 1 Ω |
| B39-1 (VV1+) or B77-82 (VV1+) - Body ground | Always | 10 kΩ or higher |
| B39-2 (VV1-) or B77-114 (VV1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the camshaft position sensor for intake camshaft installation.
Camshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the timing rotor of the intake camshaft.
Camshaft timing rotor does not have any cracks or deformation.
Perform "Inspection After Repair" after replacing the intake camshaft.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Replace the camshaft position sensor (for intake camshaft).
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0340, P0342 or P0343 is output | A |
| DTC is not output | B |
If the engine does not start, replace the ECM.
A
B
Disconnect the camshaft position sensor for intake camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B39-3 (VC) - B77-113 (VCV1) | Always | Below 1 Ω |
| B39-3 (VC) or B77-113 (VCV1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG