The ECM activates the intake air control valve actuator (for tumble control valve), which opens and closes the Tumble Control Valve (TCV). The ECM activates the DC motor based on engine speed, coolant temperature, intake air temperature and other conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P2009 | Intake Manifold Runner Control Circuit Low (Bank 1) | Both of the following conditions continue for 1 second (1 trip detection logic).
(a) The output duty of the intake air control valve actuator is 34% or higher. (b) The current of the intake air control valve actuator is less than 0.35 A. |
·
Open or short in intake air control valve actuator (for tumble control valve) circuit ·
Intake air control valve actuator (for tumble control valve) ·
Intake manifold ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
| P2010 | Intake Manifold Runner Control Circuit High (Bank 1) | Either of the following conditions continues for 6 times or more (1 trip detection logic).
(a) The motor drive IC has overcurrent. (b) The motor drive IC overheats. |
·
Open or short in intake air control valve actuator (for tumble control valve) circuit ·
Intake air control valve actuator (for tumble control valve) ·
Intake manifold ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Applies |
When the voltage of the intake air control valve actuator deviates from the standard range, the ECM determines that a malfunction has occurred and stores a DTC.
| Related DTCs | P2009: Intake air control valve actuator for tumble control valve range check (low current)
P2010: Intake air control valve actuator for tumble control valve range check (high current) |
| Required Sensors/Components (Main) | Intake air control valve actuator (for tumble control valve) |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second: P2009
6 times: P2010 |
| MIL Operation | Immediate |
| Sequence Operation | None |
| Monitor runs whenever the following DTCs are not stored | None |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Starter | Off |
| Output duty cycle | 34% or higher |
| Difference between motor current and previous motor current | Less than 0.2 A |
| All of the following conditions are met | - |
| Battery voltage | 8 V or higher |
| Starter | Off |
| Intake air control valve actuator for tumble control valve current | Less than 0.35 A |
| Motor drive IC high current limiter monitor input | Fail |
| Intake air control valve actuator for tumble control valve current | Higher than 0.35 A |
| Motor drive IC high current limiter monitor input | Pass |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.
Check that the engine coolant temperature is 60°C (140°F) or higher.
Wait approximately 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2009 or P2010.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Refer to DTC P2004.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P2004
Read freeze frame data using the Techstream. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the intake air control valve actuator (for tumble control valve).
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE AIR CONTROL VALVE ACTUATOR(for TCV)>REMOVAL
Inspect the intake manifold for the tumble control valve operation.
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Wait approximately 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2009 or P2010 is output | A |
| DTC is not output | B |
A
B