Refer to DTC P0300.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P0300
Refer to DTC P2195.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>P2195
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P219A | Bank 1 Air-Fuel Ratio Imbalance | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | ·
Fuel injector assembly ·
Intake system ·
Gas leaks from exhaust system ·
Ignition system ·
Compression pressure ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on | DTC stored | DTC for Mexico Models
- Not apply |
The ECM uses the air fuel ratio sensor and crankshaft position sensor to monitor the difference in air fuel ratios between the cylinders caused by differences in injection volumes between the cylinders, leakage in the intake or exhaust system, etc.
When the air fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.
When the system detects a difference in air fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.
The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in air fuel ratios between the cylinders, which it determines to be a problem.
| Related DTCs | P219A: Air fuel ratio cylinder imbalance monitor |
| Required Sensors/Components (Main) | Air fuel ratio sensor
Crankshaft position sensor |
| Required Sensors/Components (Related) | Mass air flow meter sub-assembly
Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds: Air fuel ratio sensor monitoring method
30 seconds: Crankshaft position sensor monitoring method |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0010 (VVT oil control valve)
P0011 (VVT system - advance) P0012 (VVT system - retard) P0013 (Exhaust VVT oil control valve) P0014 (Exhaust VVT system - advance) P0015 (Exhaust VVT system - retard) P0016 (VVT system - misalignment) P0017 (Exhaust VVT system - misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0327, P0328 (Knock control sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0351 - P0354 (Igniter) P0365, P0367, P0368 (Exhaust camshaft position sensor) P0500 (Vehicle speed sensor) |
| Air fuel ratio sensor status | Activated |
| Engine speed | 1600 rpm or higher, and less than 2400 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Fuel system status | Closed loop |
| Mass air flow | 24 gm/sec or more, and less than 34 gm/sec |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Engine speed | 450 rpm or higher, and less than 1100 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or higher |
| Air fuel ratio sensor monitoring method criteria (rich side imbalance) | 0.133 or more |
| Crankshaft position sensor monitoring method criteria (lean side imbalance) | 1.0 or more |
Refer to detailed information in Checking Monitor Status.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>CHECKING MONITOR STATUS
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $81 | $81 | Multiply by 0.00003 | No dimension | Monitoring method using A/F sensor |
| Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
| $81 | $82 | Multiply by 0.001 | No dimension | Monitoring method using crank angle sensor |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Drive the vehicle at 60 km/h (37 mph) or higher for 2 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
It is acceptable to turn electrical loads on while driving.
Idle the engine for 2 minutes or more [C].
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [E].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Accelerate the vehicle from 30 to 60 km/h (19 to 37 mph) over a period of approximately 10 to 20 seconds.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 37 mph).
Drive the vehicle at 60 km/h (37 mph) or more for 5 seconds or more [F].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [G].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Accelerate the vehicle from 30 to 60 km/h (19 to 37 mph) over a period of approximately 10 to 20 seconds.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 37 mph).
Drive the vehicle at 60 km/h (37 mph) or more for 5 seconds or more [H].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Repeat steps [G] and [H] above at least 2 times [I].
Idle the engine for 1 minute or more [J].
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P219A.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the following procedure.
If no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Refer to A/F Sensor Determination (worst value) #1, Engine Speed Fluctuation Avg (worst value) #1 to #4, Cylinder #1 to #4 Misfire Count, Short FT #1 and Long FT #1 in the Data List / Active Test.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P219A is output | A |
| DTC P219A and other DTCs are output | B |
If any DTCs other than P219A are output, troubleshoot those DTCs first.
A
B
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
Vehicle Speed
Engine Speed
Calculate Load
Accelerator Idle Position
Short FT #1
Long FT #1
Cylinder #1 Misfire Count to Cylinder #4 Misfire Count
A/F Sensor Determination (worst value) #1
Engine Speed Fluctuation Avg (worst value) #1 to #4
When the sum of Short FT #1 and Long FT #1 is positive, the engine is running lean, and when the sum is negative, the engine is running rich.
| DTC stored during idling | It is possible to conclude that the problem was detected due to a "lean imbalance" (detected using crankshaft speed variation). |
| DTC stored while vehicle being driven | It is possible to conclude that the problem was detected due to a "rich imbalance" (detected using the air fuel ratio sensor). |
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count") increases while idling or driving the vehicle, proceed to step 6.
Perform inspections while focusing on the cylinder whose misfire count has increased.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / Fuel System / Details / A/F SENSOR DETERMINATION B1 and ENGINE SPEED FLUCTUATION AVERAGE B1.
Check the Test Result (A/F SENSOR DETERMINATION B1 and ENGINE SPEED FLUCTUATION AVERAGE B1).
| Result | Proceed to |
|---|---|
| A/F SENSOR DETERMINATION is Fail | A |
| A/F SENSOR DETERMINATION and ENGINE SPEED FLUCTUATION AVERAGE are Fail | B |
| ENGINE SPEED FLUCTUATION AVERAGE is Fail* |
When the results of A/F SENSOR DETERMINATION and ENGINE SPEED FLUCTUATION AVERAGE are both Pass, drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern again.
If both results are still Pass, proceed to step 4.
*: Perform inspections while focusing on the cylinder whose engine speed fluctuation value ("Engine Speed Fluctuation Avg (worst value) #1" to "Engine Speed Fluctuation Avg (worst value) #4") was the largest.
A
B
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Gas Misfire / Cylinder #1 to #4 Misfire Count.
| Active Test Display |
|---|
| Control the Injection Volume |
| Data List Display |
|---|
| Cylinder #1 Misfire Count |
| Cylinder #2 Misfire Count |
| Cylinder #3 Misfire Count |
| Cylinder #4 Misfire Count |
When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Intake System).
Perform the Control the Injection Volume operation with the engine idling.
Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #4 Misfire Count") while decreasing the injection volume in 5% increments.
The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Check for exhaust gas leaks.
No gas leaks.
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leakage in intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the spark plug of the cylinder causing the imbalance.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor].
Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
Check the intake valve for deposits.
As the DTC may have been stored due to deposits on the intake valve, remove the cylinder head and check the intake valve.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
P219A is not output.
| Proceed to |
|---|
| NEXT |
NEXT