Home › Engine / Hybrid System › 2AR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD
RM30B0U _51 Engine / Hybrid System _009090 2AR-FE INTAKE / EXHAUST _0049679 EXHAUST MANIFOLD A

2AR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR

a.

Install the No. 1 manifold converter insulator with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 2.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A195981

Install a new gasket to the cylinder head.


b.
A293724
1.417,1.698 1.5,1.854 0.083,0.156 10 1 0.688,0.021 0.781,0.177 0.094,0.156 10 2 2.708,0.042 2.802,0.208 0.094,0.167 10 3 0.281,1.667 0.396,1.833 0.115,0.167 10 4 3.135,1.656 3.219,1.865 0.083,0.208 10 5

Temporarily install the exhaust manifold converter sub-assembly with the 5 nuts.


c.

Tighten the 5 nuts in the sequence shown in the illustration.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 3.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 2 exhaust manifold heat insulator with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 4 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 5.INSTALL NO. 2 MANIFOLD STAY

a.

Install the No. 2 manifold stay with the bolt and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 6.INSTALL MANIFOLD STAY

a.

Install the manifold stay with the bolt and nut.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 7.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 8.INSTALL RADIATOR HOSE CLAMP

Hide 9.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 10.INSTALL FRONT EXHAUST PIPE SUB-ASSEMBLY

a.
A077857
3.041,2.038 3.409,2.13 0.367,0.092

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.63 in.)


If the length is less than the minimum, replace the compression spring.


b.

Using a wire brush, remove any foreign matter from the gasket installation surface.


c.
A076194
2.031,1.583 1.563,1.719 1.563,1.719 1.396,1.719 true 2.438,0.979 3.042,0.979 true 1.188,1.625 1.406,1.802 0.219,0.177 10 *1 3.063,0.885 3.281,1.063 0.219,0.177 10 *2
*1 Gasket
*2 Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




d.

Install a new gasket to the front exhaust pipe sub-assembly.


e.

Install the front exhaust pipe sub-assembly with the 2 compression springs and 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

Connect the heated oxygen sensor connector.