Home › Engine / Hybrid System › 2AR-FE COOLING › RADIATOR
RM30B0U _51 Engine / Hybrid System _009233 2AR-FE COOLING _0050393 RADIATOR A

2AR-FE COOLING  RADIATOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL FAN SHROUD

a.

Install the fan shroud with the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 2.INSTALL COOLER CONDENSER ASSEMBLY

a.

Attach the 2 guides and install the cooler condenser assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER>INSTALLATION


Hide 3.INSTALL NO. 2 FAN SHROUD

a.

Attach the 2 claws to install the No. 2 fan shroud.


b.

Install the 2 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 4.INSTALL LOWER RADIATOR SUPPORT

a.

Install the 2 lower radiator supports to the fan shroud.


Hide 5.INSTALL WATER BY-PASS PIPE

a.

Install the water by-pass pipe to the radiator, and slide the hose clamp to secure it.


b.

Attach the 2 clamps to install the water by-pass pipe.


Hide 6.INSTALL NO. 2 RADIATOR HOSE

a.

Install the No. 2 radiator hose to the radiator assembly, and slide the clamp to secure it.

HINT:

Install the hose clamp with the claw facing downward.



Hide 7.INSTALL RADIATOR HOSE SUB-ASSEMBLY

a.

Install the radiator hose sub-assembly to the radiator assembly and water by-pass pipe, and slide the 2 hose clamps to secure it.


Hide 8.INSTALL RADIATOR ASSEMBLY

a.

Install the radiator assembly together with the fan shround.

NOTICE:

Make sure that both lower radiator supports are attached to the fan shround.



Hide 9.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the radiator assembly, and slide the hose clamp to secure it.


Hide 10.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the water by-pass pipe, and slide the hose clamp to secure it.


Hide 11.CONNECT NO. 2 RADIATOR HOSE

Hide 12.CONNECT RADIATOR HOSE SUB-ASSEMBLY

a.

Connect the radiator hose sub-assembly to the cylinder head sub-assembly, and slide the hose clamp to secure it.


Hide 13.INSTALL RADIATOR HOSE HOSE CLAMP

a.

Install the 2 radiator hose hose clamps.


b.

Connect the No. 8 and No. 9 water by-pass hose to each radiator hose hose clamp.


Hide 14.INSTALL UPPER RADIATOR SUPPORT

a.

Install the upper radiator support with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 15.INSTALL NO. 1 RADIATOR SUPPORT

a.

Install the 2 No. 1 radiator supports with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 16.CONNECT WIRE HARNESS

a.

Connect the 2 cooling fan motor connectors.


b.

Attatch the 9 wire harness clamps to connect the wire harness.


Hide 17.CONNECT LIQUID PIPE SUB-ASSEMBLY

Hide 18.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 19.INSTALL RADIATOR UPPER AIR GUIDE PLATE

a.

Install the radiator upper air guide plate with the 7 clips.


Hide 20.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly with the 3 bolts.


b.

Connect the horn connector.


Hide 21.CONNECT HOOD LOCK CONTROL CABLE ASSEMBLY

a.

Attach the clamp to connect the hood lock contorl cable assembly.


Hide 23.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 26.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 29.INSTALL NO. 1 ENGINE UNDER COVER