Home › Engine / Hybrid System › 2AR-FE LUBRICATION › OIL PUMP
RM30B0U _51 Engine / Hybrid System _009177 2AR-FE LUBRICATION _0050593 OIL PUMP A

2AR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TIMING CHAIN COVER ASSEMBLY

a.

Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.


b.

Install the oil hole cover gasket to the stiffening crankcase.


c.

Install the 2 oil pump gaskets to the stiffening crankcase.


d.
A196862
0.875,2.719 0.958,3.031 0.958,3.031 0.958,3.135 true 2.271,2.5 2.365,2.74 2.365,2.74 2.365,2.833 true 2.313,2.865 2.552,3.042 0.24,0.177 10 *2 0.885,3.146 1.104,3.313 0.219,0.167 10 *1
*1 Drive Rotor Spline
*2 Crankshaft Timing Sprocket


Align the drive rotor splines and crankshaft timing sprocket as shown in the illustration.


e.

Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

A297602
5.188,1.604 5.74,1.948 5.74,1.948 5.938,1.948 false 5.219,3.302 5.458,2.823 5.458,2.823 5.667,2.823 false 5.385,3.552 5.792,3.25 5.792,3.25 5.99,3.25 false 5.354,5.417 5.583,4.792 5.583,4.792 5.75,4.792 false 5.552,5.74 6.01,5.292 6.01,5.292 6.219,5.292 false 2.042,7.292 2.781,7.292 2.781,7.292 2.781,7.438 false 0.115,0.094 0.531,0.302 0.417,0.208 10 A - A 0.042,0.604 0.479,0.792 0.438,0.188 10 B - B 0.615,1.458 1.083,1.646 0.469,0.188 10 C - C 0.365,3.698 0.854,3.885 0.49,0.188 10 D - D 3.656,4.063 3.854,4.26 0.198,0.198 10 *f 2.479,3.604 2.979,3.781 0.5,0.177 10 D - D 2.052,2.396 2.26,2.594 0.208,0.198 10 E 2.063,1.667 2.573,1.865 0.51,0.198 10 C - C 1.948,0.854 2.156,1.073 0.208,0.219 10 E 2.292,0.281 2.75,0.479 0.458,0.198 10 A - A 3.177,0.552 3.604,0.75 0.427,0.198 10 B - B 3.688,0.917 3.896,1.115 0.208,0.198 10 *d 3.406,1.927 3.604,2.115 0.198,0.188 10 *e 4.49,1.26 4.938,1.469 0.448,0.208 10 A - A 5.552,1.021 5.771,1.229 0.219,0.208 10 *g 6,1.823 6.198,2.021 0.198,0.198 10 *h 5.719,2.719 5.938,2.906 0.219,0.188 10 *b 6.052,3.135 6.229,3.323 0.177,0.188 10 *i 5.823,4.104 6.479,4.302 0.656,0.198 10 *h 4.25,2.927 5.135,3.125 0.885,0.198 10 B - B, D - D 4.458,5.219 4.927,5.417 0.469,0.198 10 C - C 5.802,4.677 6.01,4.875 0.208,0.198 10 *c 6.271,5.167 6.438,5.375 0.167,0.208 10 *j 3.792,5.938 3.979,6.125 0.188,0.188 10 *a 1.396,7.094 1.594,7.281 0.198,0.188 10 *h 1.104,5.406 1.385,5.635 0.281,0.229 10 E 2.708,7.458 2.906,7.646 0.198,0.188 10 *h 4.99,6.271 5.146,6.458 0.156,0.188 10 *i 4.302,3.677 4.5,3.865 0.198,0.188 10 *a
*a 3.0 mm (0.118 in.) or more *b 7.0 mm (0.276 in.) or more
*c 13.0 mm (0.512 in.) or more *d 28 mm (1.10 in.)
*e 25 mm (0.984 in.) *f 26 mm (1.02 in.)
*g 2.5 mm (0.0984 in.) *h 3.0 mm (0.118 in.)
*i 5.0 mm (0.197 in.) *j 7.0 mm (0.276 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.


Apply Seal Packing as Follows:
Area Seal Packing Diameter (Round) Distance from Edge of Cover to Center of Seal Packing Seal Packing Application Length
Seal Packing Dimension (Flat)
Dashed Line 3.0 mm (0.118 in.) 2.5 mm (0.0984 in.) -
-
A - A 3.0 mm (0.118 in.) 2.5 mm (0.0984 in.) -
-
B - B 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 28 mm (1.10 in.)
Width of 7.0 mm (0.276 in.) or more and thickness of 3.0 mm (0.118 in.) or more
C - C 7.0 mm (0.276 in.) 5.0 mm (0.197 in.) 25 mm (0.984 in.)
Width of 13.0 mm (0.512 in.) or more and thickness of 3.0 mm (0.118 in.) or more
D - D 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 26 mm (1.02 in.)
Width of 7.0 mm (0.276 in.) or more and thickness of 3.0 mm (0.118 in.) or more
E 3.0 mm (0.118 in.) 3.0 mm (0.118 in.) -
-


NOTICE:
·

When the contact surfaces are wet, clean the surfaces with non-residue solvent before applying seal packing.

·

Install the timing chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

After applying seal packing to the timing chain cover, install the engine mounting bracket within 10 minutes.

·

Do not add oil for at least 4 hours after the installation.

·

Do not start the engine for at least 4 hours after the installation.




f.
A241476
1.917,0.135 1.823,0.135 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Nut


Temporarily install the timing chain cover with the 17 bolts and 2 nuts.

Bolt Length:
Item Length Thread Diameter
Bolt A 30 mm (1.18 in.) 8 mm (0.315 in.)
Bolt B 35 mm (1.38 in.) 10 mm (0.394 in.)
Bolt C 45 mm (1.77 in.) 8 mm (0.315 in.)


NOTICE:

Make sure there is no oil on the bolts. If there is oil on the bolts, clean them before installing them.



g.
A296891
0.74,1.573 0.938,1.74 0.198,0.167 10 14 0.76,1.833 0.958,2 0.198,0.167 10 13 2.177,1.875 2.375,2.042 0.198,0.167 10 10 1.948,2.01 2.146,2.177 0.198,0.167 10 11 0.927,1.99 1.125,2.156 0.198,0.167 10 12 0.698,1.323 0.896,1.49 0.198,0.167 10 15 0.781,1.031 0.979,1.198 0.198,0.167 10 16 0.698,0.406 0.896,0.573 0.198,0.167 10 17 0.719,0.146 0.917,0.313 0.198,0.167 10 18 1.813,1.448 2.01,1.615 0.198,0.167 10 19 2.292,1 2.417,1.177 0.125,0.177 10 1 0.854,0.802 0.979,0.979 0.125,0.177 10 2 2.385,0.813 2.51,0.99 0.125,0.177 10 3 0.854,0.583 0.979,0.76 0.125,0.177 10 4 2.594,0.156 2.719,0.333 0.125,0.177 10 5 2.542,0.438 2.667,0.615 0.125,0.177 10 6 2.302,1.208 2.427,1.385 0.125,0.177 10 7 2.396,1.458 2.521,1.635 0.125,0.177 10 8 2.396,1.667 2.521,1.844 0.125,0.177 10 9

Tighten the 17 bolts and 2 nuts in several steps in the sequence shown in the illustration.

Torque:
for bolt 1, 2, 3 and 4 : 55 N*m (561 kgf*cm, 41 ft.*lbf)
except bolt 1, 2, 3 and 4 : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 2.INSTALL ENGINE MOUNTING BRACKET RH

a.
A296892
1.583,1.771 1.708,1.948 0.125,0.177 10 4 2.813,1.677 2.938,1.854 0.125,0.177 10 1 1.479,0.802 1.604,0.979 0.125,0.177 10 2 2.979,0.552 3.104,0.729 0.125,0.177 10 3

Temporarily install the engine mounting bracket RH with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
for bolt 1, 2 and 3 : 55 N*m (561 kgf*cm, 41 ft.*lbf)
for bolt 4 : 21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

After applying seal packing to the timing chain cover assembly, install the engine mounting bracket RH within 10 minutes.



Hide 6.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 7.INSTALL SPARK PLUG TUBE GASKET

a.
A196889
2.281,1.302 2.021,0.5 false 2.656,1.271 3.052,1.708 false 3.052,1.708 3.146,1.708 false 1.104,0.177 0.99,0.177 0.99,0.177 0.885,0.594 false 2.021,0.5 1.896,0.5 false 1.135,0.052 1.375,0.219 0.24,0.167 10 *1 3.177,1.594 3.406,1.75 0.229,0.156 10 *3 1.698,0.385 1.927,0.542 0.229,0.156 10 *2
*1 Upper Surface
*2 Inner Lip
*3 Outer Lip


Visually check the spark plug tube gasket.

OK:
Area Specified Condition
Upper surface No scratches or deformation
Outer lip No scratches or deformation
Inner lip No scratches


If the result is not as specified, replace the spark plug tube gasket.


b.
A196890

Install the 4 spark plug tube gaskets to the cylinder head cover.

NOTICE:

After pressing in the spark plug tube gasket, make sure the gasket protrudes 1.0 mm (0.0394 in.) or less from the cylinder head cover.



Hide 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to 2 new camshaft bearing cap oil hole gaskets and a new gasket.


b.

Install the gasket to the No. 2 camshaft bearing cap.


c.

Install the 2 camshaft bearing cap oil hole gaskets to the No. 1 camshaft bearing cap.


d.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surface.



e.
A196891
2.146,1.948 2,1.948 2,1.948 1.76,2.479 false 1.135,2.396 1.229,2.396 1.229,2.396 1.292,2.667 false 2.438,2.365 2.292,2.365 2.292,2.365 2.146,2.688 false 0.542,1.99 0.76,2.156 0.219,0.167 10 *1 2.198,1.854 2.417,2.042 0.219,0.188 10 *1 0.906,2.281 1.156,2.448 0.25,0.167 10 *2 2.49,2.281 2.729,2.448 0.24,0.167 10 *3 1.49,2.948 1.677,3.125 0.188,0.177 10 A 1.781,2.948 1.958,3.115 0.177,0.167 10 A
*1 Seal Packing
*2 Timing Chain Cover
*3 Camshaft Housing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


Application width A:

5.0 mm (0.197 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




f.
A297604
3.01,1.302 3.25,1.219 3.25,1.219 3.25,1.344 false 0.729,0.375 0.646,0.115 0.646,0.115 0.552,0.115 false 0.25,0.292 0.479,0.51 0.229,0.219 10 9 0.125,0.854 0.302,1.063 0.177,0.208 10 8 0.219,1.865 0.438,2.063 0.219,0.198 10 7 1.125,1.948 1.375,2.135 0.25,0.188 10 6 1.5,1.958 1.938,2.135 0.438,0.177 10 5, 18 2.167,1.969 2.469,2.135 0.302,0.167 10 17 3.125,1.802 3.354,2 0.229,0.198 10 16 3.208,1.406 3.385,1.625 0.177,0.219 10 B 3.167,0.792 3.375,1.042 0.208,0.25 10 15 2.646,0.729 3.073,0.917 0.427,0.188 10 3, 21 1.823,0.729 2.281,0.896 0.458,0.167 10 1, 19 1.26,0.74 1.688,0.917 0.427,0.177 10 2, 20 3.052,0.26 3.313,0.5 0.26,0.24 10 14 2.188,0.094 2.406,0.313 0.219,0.219 10 13 1.656,0.094 2.063,0.302 0.406,0.208 10 4, 12 1.281,0.094 1.521,0.313 0.24,0.219 10 11 0.781,0.042 1.031,0.26 0.25,0.219 10 10 0.406,0.063 0.604,0.281 0.198,0.219 10 A

Align the cylinder head cover with pin A. Then align the cylinder head cover with pin B and install the cylinder head cover.


g.

Install 3 new seal washers and the 16 bolts, and then tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not add oil for at least 4 hours after the installation.

·

Do not start the engine for at least 4 hours after the installation.




Hide 10.CONNECT ENGINE WIRE

a.

Connect the connectors and clamps, and then connect the engine wire to the engine.