Home › Suspension › FRONT SUSPENSION › FRONT STABILIZER BAR
RM30B0U _53 Suspension _009473 FRONT SUSPENSION _0051206 FRONT STABILIZER BAR A

FRONT SUSPENSION  FRONT STABILIZER BAR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FRONT STABILIZER BAR BUSHING LH

C148690
1.833,1.156 2.01,1.031 false 2.021,1.031 2.521,1.031 false 0.823,2.49 1.667,2.49 false 1.427,2.792 1.667,2.792 false 1.427,2.781 1.427,2.49 false 2.583,0.948 2.896,1.104 0.313,0.156 10 *a 0.667,2.406 0.979,2.563 0.313,0.156 10 *b 2.208,0.438 2.521,0.594 0.313,0.156 10 *c 2.313,1.448 2.625,1.604 0.313,0.156 10 *d
*a Stopper
*b Dust Lip
*c Front of the Vehicle
*d Inside of the Vehicle


a.

Install the front stabilizer bar bushing to the front stabilizer bar as shown in the illustration.

NOTICE:
·

Install the front stabilizer bar bushing so that the dust lips face the outside of the vehicle.

·

Install the front stabilizer bar bushing so that the cutouts face the rear of the vehicle.




Hide 2.INSTALL FRONT STABILIZER BAR BUSHING RH

HINT:

Use the same procedure described for the LH side.


Hide 3.INSTALL FRONT STABILIZER BAR

a.

Install the front stabilizer bar to the front suspension crossmember so that the identification mark is positioned on the right side of the vehicle.

C149516
1.708,2.052 1.823,1.823 false 1.833,1.823 2.271,1.823 false 2.333,1.75 2.646,1.906 0.313,0.156 10 *a 3.313,1.375 3.625,1.531 0.313,0.156 10 *b 4.531,0.125 4.844,0.281 0.313,0.156 10 *c
*a Identification Mark *b Front of the Vehicle
*c Top of the Vehicle - -



Hide 4.INSTALL FRONT SUSPENSION MEMBER BRACE

a.
C232258
0.292,1.052 0.646,1.052 true 2.708,1.052 3.104,1.052 true 0.115,0.969 0.427,1.125 0.313,0.156 10 *a 3.125,0.958 3.375,1.156 0.25,0.198 10 *a
*a Protrusion


Install the front suspension member brace with the 8 bolts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)

NOTICE:

After installing the front suspension member brace, mark sure that the protrusions of the front stabilizer bar bushings are visible.



Hide 5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.



Hide 6.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




b.

Tighten the bolts on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

C234336
3.469,0.115 3.781,0.271 0.313,0.156 10 *a 1.333,5.583 1.646,5.74 0.313,0.156 10 *b 2.229,5.573 2.542,5.729 0.313,0.156 10 *c 4.781,5.563 5.094,5.719 0.313,0.156 10 *b 5.646,5.573 5.958,5.729 0.313,0.156 10 *c
*a Front of the Vehicle *b OK
*c NG - -


SST
09670-00020  

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


c.

Lower the engine lifter.


d.

Install the rear engine mounting insulator with bolts A and B, and nuts C and D by tightening them in several steps.

C232246
3.271,1.813 3.427,2.01 0.156,0.198 10 A 4.375,1.927 4.531,2.125 0.156,0.198 10 B 3.188,2.385 3.344,2.583 0.156,0.198 10 C 4.542,2.625 4.698,2.823 0.156,0.198 10 D

Torque:
Bolt A, B, Nut C, D : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

Temporarily tighten bolt A, and then fully tighten the 2 bolts and 2 nuts in the order of B, D, C, and A.



Hide 7.INSTALL FRONT SUSPENSION MEMBER REAR BRACE LH

a.
C149508
1.49,0.531 1.646,0.729 0.156,0.198 10 A 2.594,0.833 2.75,1.031 0.156,0.198 10 B 0.854,1.802 1.01,2 0.156,0.198 10 C

Install the front suspension member rear brace LH with the 3 bolts.

Torque:
Bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
Bolt B, C : 93 N*m (948 kgf*cm, 69 ft.*lbf)

NOTICE:

Temporarily tighten bolts A and B, and then fully tighten the 3 bolts in the order of C, B, and A.



Hide 8.INSTALL FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 9.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.

Install the reinforcement with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 10.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.

Install the reinforcement with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)


Hide 11.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Connect the front lower No. 1 suspension arm sub-assembly to the lower arm ball joint with the bolt and 2 nuts.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)


Hide 12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 13.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 14.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH with the 2 nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 16.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 17.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 18.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 19.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 20.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH with the 3 clips.


Hide 21.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH with the 3 clips.


Hide 22.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 23. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down at the corners several times to stabilizer the suspension.


Hide 24.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C279176
1.427,0.479 1.521,0.177 false 1.531,0.177 1.979,0.177 false 2.229,1.292 2.542,1.448 0.313,0.156 10 *a 2.115,3 2.427,3.156 0.313,0.156 10 *b 2.094,0.125 2.552,0.323 0.458,0.198 10 SST 0.979,0.25 1.135,0.448 0.156,0.198 10 A 1.042,1.917 1.198,2.115 0.156,0.198 10 B
*a Fulcrum Length
*b Turn


Using SST, tighten bolt A.

SST
09961-01270  

Torque:
without SST : 233 N*m (2376 kgf*cm, 172 ft.*lbf)
with SST : 172 N*m (1754 kgf*cm, 127 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.

·

Use a torque wrench with a fulcrum length of 425 mm (1.39 ft.).

·

The torque value for use with SST is effective when SST is parallel to the torque wrench.

·

The final torque must be applied under standard vehicle height conditions.




b.

Tighten bolt B.

Torque:
214 N*m (2182 kgf*cm, 158 ft.*lbf)


Hide 27.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT