Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL
RM30B0U _58 Vehicle Interior _009873 INTERIOR PANELS / TRIM _0054288 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL UPPER INSTRUMENT PANEL

a.

Attach the 8 clips to install the upper instrument panel.


b.

Install the 2 bolts <C> or <D>.


c.

Install the 2 bolts <B>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect each connector.

B341008
4.99,5.094 5.302,5.292 0.313,0.198 10 *1 1.646,0.583 1.958,0.781 0.313,0.198 10 *2 4.573,4.542 4.885,4.74 0.313,0.198 10 *4 5.396,0.583 5.708,0.781 0.313,0.198 10 *2 5.625,4.865 5.938,5.063 0.313,0.198 10 *1 4.49,5.177 4.802,5.375 0.313,0.198 10 *3
*1 Bolt <B> *2 Bolt <C> or <D>
*3 Airbag Connector A *4 Airbag Connector B



e.
B342358
1.458,0.188 1.698,0.188 1.698,0.188 1.781,0.469 true 1.344,1.177 1.552,1.177 1.552,1.177 1.688,1.583 true 2.375,0.177 2.615,0.177 2.615,0.177 2.698,0.458 true 2.354,2.031 2.594,2.031 2.594,2.031 2.656,1.635 true 0.052,0.063 0.365,0.26 0.313,0.198 10 *1 0.052,0.99 0.365,1.188 0.313,0.198 10 *2 1.313,0.104 1.625,0.302 0.313,0.198 10 *3 2.229,0.073 2.542,0.271 0.313,0.198 10 *a 1.198,1.083 1.51,1.281 0.313,0.198 10 *3 2.208,1.927 2.521,2.125 0.313,0.198 10 *a
*1 Airbag Connector A
*2 Airbag Connector B
*3 Lock Slider
*a Lock Position


Connect the 2 airbag connectors A and B.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



f.

Check that the lock slider is in the lock position.


Hide 2.INSTALL FRONT PILLAR GARNISH LH

Hide 3.INSTALL FRONT PILLAR GARNISH RH

Hide 6.INSTALL NO. 1 SPEAKER HOLE COVER

HINT:

Use the same procedure described for the No. 2 speaker hole cover.


Hide 7.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B337786
1.875,1.563 2.031,1.76 0.156,0.198 10 false .
V100155

Protective Tape


Apply protective tape as shown in the illustration.


b.

Attach the 2 hinges to install the glove compartment door assembly.


c.
B337784
2.031,1.448 2.198,1.688 0.167,0.24 10 false . 1.969,1.417 2.125,1.615 0.156,0.198 10 false .
V100155

Protective Tape


While pushing in the sides of the glove compartment door assembly, attach the 2 stoppers.


d.

Connect the glove compartment door stopper sub-assembly.


Hide 8.INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL

a.

Attach the 4 clips to install the upper instrument cluster finish panel.


Hide 9.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.

w/ Smart Entry and Start System:

Connect the connector.


b.

Attach the 13 clips to install the No. 2 instrument panel garnish sub-assembly.

B337782


Hide 10.INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 11.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (except Automatic Air Conditioning System)

a.

Connect each connector.


b.
B337780

Attach the 2 clips to install the lower center instrument cluster finish panel sub-assembly.


Hide 12.INSTALL HEADLIGHT DIMMER SWITCH

Hide 13.INSTALL COMBINATION METER ASSEMBLY

Hide 14.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL

a.
B337776

Attach the 11 clips and claw to install the No. 1 instrument cluster finish panel.


Hide 15.INSTALL RADIO RECEIVER ASSEMBLY

Hide 16.INSTALL TELLTALE LIGHT ASSEMBLY

Hide 17.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B337770

Attach the 2 clips and 2 claws to install the No. 3 instrument panel register assembly.


Hide 18.INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B337772

Attach the 3 clips and claw to install the No. 4 instrument panel register assembly.


Hide 19.INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

a.

Attach the 6 clips and 2 claws to install the center No. 1 instrument cluster finish panel.

B337766


Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION