Home › Vehicle Interior › INTERIOR PANELS / TRIM › UPPER INSTRUMENT PANEL
RM30B0U _58 Vehicle Interior _009873 INTERIOR PANELS / TRIM _0054288 UPPER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  UPPER INSTRUMENT PANEL  REMOVAL  


PROCEDURE

Hide 1.TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.


B339322
0.177,0.448 0.792,0.646 0.615,0.198 10 Code 3.688,0.448 4.458,0.646 0.771,0.198 10 Shape 5.917,0.448 6.688,0.646 0.771,0.198 10 Shape 2.583,0.448 3.198,0.646 0.615,0.198 10 Code 4.844,0.448 5.458,0.646 0.615,0.198 10 Code 0.219,1.292 0.677,1.49 0.458,0.198 10 <A> 2.615,1.271 3.073,1.469 0.458,0.198 10 <B> 4.875,1.26 5.333,1.458 0.458,0.198 10 <C> 0.219,2.188 0.677,2.385 0.458,0.198 10 <D> 2.01,0.948 2.323,1.146 0.313,0.198 10 φ 5 1.885,2.052 2.958,2.25 1.073,0.198 10 (0.236) 1.885,1.563 2.958,1.76 1.073,0.198 10 (0.551) 1.906,1.365 2.521,1.563 0.615,0.198 10 L = 14 4.281,0.948 4.594,1.146 0.313,0.198 10 φ 8 4.177,1.146 5.25,1.344 1.073,0.198 10 (0.315) 4.188,1.365 4.802,1.563 0.615,0.198 10 L = 21 4.177,1.563 5.25,1.76 1.073,0.198 10 (0.827) 6.552,0.948 6.865,1.146 0.313,0.198 10 φ 6 6.458,1.563 6.906,1.76 0.448,0.198 10 (0.787) 6.469,1.365 7.083,1.563 0.615,0.198 10 L = 20 6.458,1.146 6.906,1.344 0.448,0.198 10 (0.236) 2.01,1.844 2.323,2.042 0.313,0.198 10 φ 6 1.885,1.156 2.958,1.354 1.073,0.198 10 (0.197) 1.906,2.292 2.521,2.49 0.615,0.198 10 L = 16 1.885,2.5 2.958,2.698 1.073,0.198 10 (0.630) 1.323,0.448 2.094,0.646 0.771,0.198 10 Shape 5.344,0.042 6.677,0.229 1.333,0.188 10 mm (in.) (L = Length)

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL

a.

Apply protective tape as shown in the illustration.


b.

Using moulding remover B, detach the 6 clips and 2 claws in the order shown in the illustration and remove the center No. 1 instrument cluster finish panel.

B337765
4.563,1.188 4.771,1.385 0.208,0.198 10 true (1) 4.365,1.354 4.594,1.552 0.229,0.198 10 true (2) 4.01,1.417 4.26,1.604 0.25,0.188 10 true (3) 3.615,1.094 3.823,1.281 0.208,0.188 10 true (4) 3.396,1.5 3.615,1.688 0.219,0.188 10 true (5) 3.104,1.583 3.323,1.781 0.219,0.198 10 true (6) 2.854,1.667 3.073,1.854 0.219,0.188 10 true (7) 2.615,1.792 2.833,1.969 0.219,0.177 10 true (8)
V100155

Protective Tape - -



Hide 5.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B337769
0.156,0.375 0.313,0.573 0.156,0.198 10 false .
V100155

Protective Tape


Apply protective tape as shown in the illustration.


b.

Using moulding remover B, detach the 2 clips and 2 claws and remove the No. 3 instrument panel register assembly.


Hide 6.REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B337771
1.969,0.573 2.125,0.771 0.156,0.198 10 false .
V100155

Protective Tape


Apply protective tape as shown in the illustration.


b.

Using moulding remover B, detach the 3 clips and claw and remove the No. 4 instrument panel register assembly.


Hide 7.REMOVE TELLTALE LIGHT ASSEMBLY

Hide 8.REMOVE RADIO RECEIVER ASSEMBLY

Hide 9.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL

B337775
2.177,2.24 2.333,2.438 0.156,0.198 10 false .
V100155

Protective Tape


a.

Apply protective tape as shown in the illustration.


b.

Using moulding remover B, detach the claw and 11 clips and remove the No. 1 instrument cluster finish panel.


Hide 10.REMOVE COMBINATION METER ASSEMBLY

Hide 11.REMOVE HEADLIGHT DIMMER SWITCH

Hide 12.REMOVE LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (except Automatic Air Conditioning System)

B337779
1.323,1.969 1.479,2.167 0.156,0.198 10 false .
V100155

Protective Tape


a.

Apply protective tape as shown in the illustration.


b.

Detach the 2 clips and remove the lower center instrument cluster finish panel sub-assembly.


c.

Disconnect each connector.


Hide 13.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

Hide 14.REMOVE NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.

Using moulding remover B, detach the 13 clips and remove the No. 2 instrument panel garnish sub-assembly.

B337781


b.
B337783

w/ Smart Entry and Start System:

Disconnect the connector.


Hide 15.REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL

B337807

a.

Using moulding remover B, detach the 4 clips and remove the upper instrument cluster finish panel.


Hide 16.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B337784
2.031,1.448 2.198,1.688 0.167,0.24 10 false . 1.969,1.417 2.125,1.615 0.156,0.198 10 false .
V100155

Protective Tape


Apply protective tape as shown in the illustration.


b.

Disconnect the glove compartment door stopper sub-assembly.


c.

Slightly bend the upper part of the glove compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it is horizontal.


d.
B337785
2.021,1.583 2.177,1.781 0.156,0.198 10 false .
V100155

Protective Tape


Pull the glove compartment door assembly toward the rear of the vehicle to detach the 2 hinges and remove it.


Hide 18.REMOVE NO. 1 SPEAKER HOLE COVER

HINT:

Use the same procedure described for the No. 2 speaker hole cover.


Hide 19.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY

Hide 20.REMOVE FRONT PILLAR GARNISH LH

Hide 21.REMOVE FRONT PILLAR GARNISH RH

Hide 22.REMOVE UPPER INSTRUMENT PANEL

a.
B342359
0.906,1.99 0.604,1.99 0.604,1.99 0.531,1.51 true 1.104,0.896 0.802,0.896 0.802,0.896 0.729,0.417 true 0.052,1.01 0.365,1.208 0.313,0.198 10 *2 0.052,0.063 0.365,0.26 0.313,0.198 10 *1 1.146,0.802 1.458,1 0.313,0.198 10 *3 0.948,1.896 1.26,2.094 0.313,0.198 10 *3
*1 Airbag Connector A
*2 Airbag Connector B
*3 Lock Slider
V100135

Pull


Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the 2 airbag connectors A and B.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



b.

Disconnect each connector.


c.

Remove the 2 bolts <B>.


d.

Remove the 2 bolts <C> or <D>.

B341008
4.99,5.094 5.302,5.292 0.313,0.198 10 *1 1.646,0.583 1.958,0.781 0.313,0.198 10 *2 4.573,4.542 4.885,4.74 0.313,0.198 10 *4 5.396,0.583 5.708,0.781 0.313,0.198 10 *2 5.625,4.865 5.938,5.063 0.313,0.198 10 *1 4.49,5.177 4.802,5.375 0.313,0.198 10 *3
*1 Bolt <B> *2 Bolt <C> or <D>
*3 Airbag Connector A *4 Airbag Connector B



e.

Pull up the upper instrument panel to detach the 8 clips and remove it.

B337797