Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL
RM30B0U _58 Vehicle Interior _009873 INTERIOR PANELS / TRIM _0054289 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL LOWER INSTRUMENT PANEL

a.

Install the lower instrument panel with the bolt <G> and 2 bolts <C> or <D> and 6 bolts <E> or <F>.

B337832
1.167,1.021 1.479,1.219 0.313,0.198 10 *1 2.406,1.104 2.719,1.302 0.313,0.198 10 *1 4.76,1.073 5.073,1.271 0.313,0.198 10 *1 3.958,2.958 4.271,3.156 0.313,0.198 10 *1 5.885,0.958 6.198,1.156 0.313,0.198 10 *1 3.135,2.927 3.448,3.125 0.313,0.198 10 *1 5.385,1.688 5.698,1.885 0.313,0.198 10 *1 1.198,2.875 1.51,3.073 0.313,0.198 10 *2 5.885,2.833 6.198,3.031 0.313,0.198 10 *2 4.99,2.135 5.302,2.333 0.313,0.198 10 *3
*1 Bolt <E> or <F> *2 Bolt <C> or <D>
*3 Bolt <G> - -



b.

Attach the 2 claws to connect the cooler thermistor.


c.

Attach the 2 claws to connect the DLC3.


d.

Attach the claw to connect the hood lock control lever.


e.

Connect each connector and attach each wire harness clamp.

B341741
0.625,2.521 0.938,2.677 0.313,0.156 10 *A 1.063,1.938 1.375,2.094 0.313,0.156 10 *B 3.698,2.958 4.01,3.115 0.313,0.156 10 *C 4.354,2.792 4.667,2.948 0.313,0.156 10 *B
*A for AWD *B w/ Power Back Door
*C w/ Smart Entry and Start System - -



Hide 2.INSTALL HEATER TO REGISTER DUCT ASSEMBLY

a.
B337830

Lower the heater to register duct assembly to attach the 6 claws and install it.


b.

Install the 2 clips.


Hide 3.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.

Attach the 3 claws to install the defroster nozzle assembly.


b.

Attach the 2 wire harness clamps and connect the connector.


Hide 4.INSTALL COWL SIDE TRIM BOARD LH

a.

Attach the clip to install the cowl side trim board LH.


b.

Install the nut.


Hide 5.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 6.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 7.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 8.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 9.INSTALL FUSE BOX OPENING COVER

a.
B337821
0.313,0.25 0.531,0.25 0.531,0.25 1.063,1.188 true 0.146,0.177 0.458,0.375 0.313,0.198 10 *1
*1 w/ Blind Spot Monitor


Connect each connector and attach the wire harness clamp.


b.
B337820

Attach the 8 clips to install the fuse box opening cover.


Hide 10.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.

Attach the 2 guides and 2 claws to install the No. 2 instrument panel under cover sub-assembly.


Hide 11.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.

Connect the connector.


b.

Attach the 2 guides and 2 claws to install the No. 1 instrument panel under cover sub-assembly.


c.

Install the 2 screws <A> or <B>.


Hide 12.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

a.
B342126
2.25,1.469 1.958,0.24 1.958,0.24 1.219,0.24 true 1.917,1.448 1.917,0.24 true 1.063,0.146 1.375,0.344 0.313,0.198 10 false *1
*1 w/ Seat Heater System


Connect each connector.


b.

Attach the 8 clips to install the lower No. 2 instrument panel finish panel.


Hide 13.INSTALL REAR CONSOLE BOX SUB-ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION